- Air outlet control servo motor
- Air conditioning harness
- Air conditioning amplifier
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000VK14 |
| Model Year Start: 2016 | Model: Sienna | Prod Date Range: [12/2015 - 08/2016] |
| Title: HEATING / AIR CONDITIONING: AIR CONDITIONING SYSTEM: B1443/43; Air Outlet Damper Control Servo Motor Circuit; 2016 MY Sienna [12/2015 - 08/2016] | ||
|
DTC |
B1443/43 |
Air Outlet Damper Control Servo Motor Circuit |
DESCRIPTION
The air outlet control servo motor sends pulse signals to indicate the damper position to the air conditioning amplifier. The air conditioning amplifier activates the motor (normal or reverse) based on these signals to move the mode damper to any position, which controls the air outlet switching.
The air conditioning amplifier communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness.
HINT:
Confirm that no mechanical problem is present because this DTC can be output when either a damper link or the damper is mechanically locked.
|
DTC Code |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B1443/43 |
Air outlet damper position sensor value does not change even if air conditioning amplifier operates air outlet control servo motor |
|
WIRING DIAGRAM
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Operate the MODE switch.
(e) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(f) Check the value(s) by referring to the table below.
Air Conditioner
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Air Outlet Servo Pulse (D) |
Air outlet servo motor target pulse / Min.: 0 Max.: 255 |
FACE: 8 (pulse) B/L: 30 to 38 (pulse) FOOT: 50 to 74 (pulse) FOOT/DEF: 80 (pulse) DEF: 97 (pulse) |
- |
OK:
The display is as specified in the Normal Condition column.
Result
|
Result |
Proceed to |
|---|---|
|
NG |
A |
|
OK (When troubleshooting according to Problem Symptoms Table) |
B |
|
OK (When troubleshooting according to the DTC) |
C |
| B |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| C |
|
|
|
2. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Active Test.
(e) Check the operation by referring to the table below.
Air Conditioner
|
Tester Display |
Test Part |
Control Rage |
Diagnostic Note |
|---|---|---|---|
|
Air Outlet Servo Pulse (D) |
Air outlet servo motor pulse |
Min.: 0, Max.: 255 |
- |
OK:
Air flow position changes in accordance with each control range.
| OK |
|
|
|
3. |
INSPECT AIR OUTLET CONTROL SERVO MOTOR |
(a) Replace the No. 1 air mix control servo motor (air outlet control servo motor) (See page
![2016 MY Sienna [12/2015 - 08/2016]; HEATING / AIR CONDITIONING: FRONT AIR CONDITIONING UNIT: DISASSEMBLY](/t3Portal/stylegraphics/info.gif)
).
HINT:
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
(b) Check for the DTC.
Result
|
Result |
Proceed to |
|---|---|
|
DTC B1443/43 is output |
A |
|
DTC B1443/43 is not output |
B |
| B |
|
|
|
4. |
INSPECT AIR CONDITIONING HARNESS |
(a) Replace the air conditioning harness (See page
).
HINT:
Since the air conditioning harness cannot be inspected while it is removed from the vehicle, replace the air conditioning harness with a new or a known good one and check that the condition returns to normal.
(b) Check for the DTC.
Result
|
Result |
Proceed to |
|---|---|
|
DTC B1443/43 is output |
A |
|
DTC B1443/43 is not output |
B |
| A |
|
| B |
|
|
|