Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJYS
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: SEAT: SEAT RAIL: REMOVAL; 2016 - 2020 MY Sienna [12/2015 -        ]

REMOVAL

PROCEDURE

1. REMOVE FUEL TANK ASSEMBLY

(a) Remove the fuel tank assembly (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE FUEL: FUEL TANK: REMOVAL 2017 - 2020 MY Sienna [08/2016 -        ]; 2GR-FKS (FUEL): FUEL TANK: REMOVAL ).

2. REMOVE REAR HEATER AIR OUTLET GRILLE ASSEMBLY

(a) Disengage the 2 clips and 2 guides, remove the rear heater air outlet grille assembly.

HINT:

Use the same procedure for the RH side and LH side.

3. REMOVE SEAT BELT ANCHOR COVER

(a) w/ Seat Belt:

(1) Disengage the 2 claws and remove the seat belt anchor cover.

HINT:

Use the same procedure for the RH side and LH side.

(b) w/o Seat Belt:

(1) Disengage the 2 claws and remove the seat belt anchor cover.

HINT:

Use the same procedure for the RH side and LH side.

4. REMOVE FLOOR CARPET MOULDING

(a) Using a screwdriver, turn the clip 90° counterclockwise to release the lock, and remove the floor carpet moulding.

HINT:

Use the same procedure for the other 7 mouldings.

5. REMOVE REAR SEAT LEG COVER LH

(a) Disengage the 2 clips, guide, claw and remove the rear seat leg cover LH.

HINT:

Use the same procedure for the LH side and RH side.

6. REMOVE REAR SEAT LEG COVER RH

(a) Disengage the 2 clips, guide and remove the rear seat leg cover RH.

HINT:

Use the same procedure for the RH side and LH side.

7. REMOVE NO. 1 REAR SEAT LEG GARNISH COVER (for Auto Access Seat Type)

(a) Remove the 3 clips and the No. 1 rear seat leg garnish cover.

HINT:

Use the same procedure for the LH side and RH side.

8. REMOVE NO. 2 REAR SEAT LEG GARNISH COVER (for Auto Access Seat Type)

(a) Remove the 2 clips and the No. 2 rear seat leg garnish cover.

HINT:

Use the same procedure for the LH side and RH side.

9. REMOVE NO. 1 FRONT SEAT LEG LH

(a) 40/40 Tip-Up Seat Type and Ottoman Seat Type:

(1) Remove the 4 nuts and No. 1 front seat leg LH.

(b) 60/40 Tip-Up Seat Type:

(1) Remove the 4 nuts and No. 1 front seat leg LH.

10. REMOVE NO. 1 FRONT SEAT LEG RH

(a) Remove the 4 nuts and No. 1 front seat leg RH.

11. REMOVE NO. 1 SEAT TRACK LOWER RAIL PROTECTOR

(a) Using a moulding remover, disengage the 8 claws and remove the No. 1 seat track lower rail protector.

Text in Illustration

*1

Moulding Remover

-

-

HINT:

Use the same procedure for the RH side and LH side.

12. REMOVE NO. 2 SEAT TRACK LOWER RAIL PROTECTOR

(a) Using a moulding remover, disengage the 8 claws and remove the No. 2 seat track lower rail protector.

Text in Illustration

*1

Moulding Remover

-

-

HINT:

Use the same procedure for the RH side and LH side.

13. REMOVE REAR SEAT OUTER TRACK ASSEMBLY RH

(a) Disengage the clips and peel back the floor carpet.

HINT:

Peel back the floor carpet enough to allow removal and installation of the rear seat outer track assembly.

(b) Remove the bolt.

(c) Using a T50 "TORX" socket wrench, remove the 3 bolts and the rear seat outer track assembly RH.

14. REMOVE REAR SEAT OUTER TRACK ASSEMBLY LH

HINT:

Use the same procedure for the RH side and LH side.

15. REMOVE REAR SEAT INNER TRACK ASSEMBLY RH

(a) Disengage the clips and peel back the floor carpet.

HINT:

Peel back the floor carpet enough to allow removal and installation of the rear seat inner track assembly.

(b) Remove the 4 nuts from the bottom of the vehicle and remove the rear seat inner track assembly RH.

16. REMOVE REAR SEAT INNER TRACK ASSEMBLY LH

HINT:

Use the same procedure for the RH side and LH side.

17. REMOVE NO. 1 SEAT LEG RH (for Auto Access Seat Type)

(a) Disengage the clips and peel back the floor carpet.

HINT:

Peel back the floor carpet enough to allow removal and installation of the rear No. 1 seat leg assembly.

(b) Disengage the 3 clamps and separate the seat wire.

(c) Remove the bolt.

(d) Using a T50 "TORX" socket wrench, remove the 3 bolts and the No. 1 seat leg assembly RH.

18. REMOVE NO. 1 SEAT LEG LH (for Auto Access Seat Type)

(a) Disengage the clips and peel back the floor carpet.

HINT:

Peel back the floor carpet enough to allow removal and installation of the rear No. 1 seat leg assembly.

(b) Remove the 4 nuts from the bottom of the vehicle and remove the No. 1 seat leg assembly LH.