Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJXY
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2018]
Title: SEAT: REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type LH Side): DISASSEMBLY; 2016 - 2018 MY Sienna [12/2015 - 08/2018]

DISASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:

Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:

Pull the seatback strap to raise the seatback.

PROCEDURE

1. REMOVE REAR NO. 2 SEAT COVER BEZEL

(a) Remove the 4 screws.

(b) Disengage the 4 guides and remove the 4 rear No. 2 seat cover bezels.

2. REMOVE REAR SEATBACK LOCK STRIKER COVER

(a) Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the rear seatback lock striker cover.

Text in Illustration

*1

Protective Tape

3. REMOVE HANDLE 3RD SEAT

(a) Remove the 2 screws.

(b) Disengage the 3 guides and separate the handle 3rd seat.

(c) Disconnect the 4 cable clamps and remove the handle 3rd seat.

4. REMOVE REAR SEATBACK LOCK CONTROL BEZEL

(a) Remove the screw.

(b) Disengage the guide and remove the rear seatback lock control bezel.

5. REMOVE REAR NO. 2 SEAT RECLINING COVER LH

(a) Disengage the 8 clips and remove the rear seatback board cover LH.

(b) Remove the 2 screws.

(c) Disengage the 2 guides and remove the rear No. 2 seat reclining cover LH.

6. REMOVE REAR NO. 2 SEAT RECLINING COVER RH

(a) Remove the 2 screws.

(b) Disengage the 2 guides and remove the rear No. 2 seat reclining cover RH.

7. REMOVE REAR NO. 2 SEAT LAP BELT ASSEMBLY CENTER WITH INNER LH

2016 - 2020 MY Sienna [12/2015 -        ]; SEAT BELT: REAR CENTER SEAT INNER BELT ASSEMBLY(for Rear No. 2 Seat): REMOVAL+

8. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY

9. REMOVE NO. 2 SEAT HEADREST ASSEMBLY

(a) Remove the 10 hog rings and 2 clips.

(b) Remove the 5 hog rings.

(c) Remove the clip and pass the No. 2 seat reclining release handle sub-assembly through the No. 2 seatback cover with pad LH.

(d) Using a screwdriver with its tip wrapped in protective tape, release the lock inside the headrest support and remove the No. 2 seat headrest assembly.

Text in Illustration

*1

Protective Tape

HINT:

When removing the headrest, turn back the No. 2 seatback cover with pad LH and make sure the cable attached to the headrest assembly does not catch on anything inside the No. 2 seatback frame sub-assembly LH.

10. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY

(a) Disengage the 8 claws and remove the 4 rear No. 2 seat headrest support assemblies.

11. REMOVE NO. 2 SEATBACK COVER WITH PAD LH

(a) Remove the No. 2 seatback cover with pad LH.

12. REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY LH

(a) Remove the 6 hog rings and No. 2 seatback cover sub-assembly LH.

13. REMOVE NO. 2 SEATBACK FRAME SUB-ASSEMBLY LH

(a) Disconnect the 3 cable clamps and separate the 2 reclining remote control cable assemblies.

(b) Remove the 4 bolts and No. 2 seatback frame sub-assembly LH.

14. REMOVE NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY

(a) Remove the nut, No. 2 seat reclining release handle sub-assembly and reclining bolt lock plate.

15. REMOVE NO. 1 RECLINING RELEASE HANDLE SUB-ASSEMBLY

(a) Remove the nut and No. 1 reclining release handle sub-assembly.

16. REMOVE RECLINING CONTROL LINK SUB-ASSEMBLY LH

(a) Remove the 2 nuts.

(b) Disconnect the cable and remove the reclining control link sub-assembly LH.

(c) Separate the rear seatback connecting wire.

(d) Remove the screw and rear seatback connecting wire.

17. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY LH

2016 - 2020 MY Sienna [12/2015 -        ]; SEAT BELT: REAR CENTER SEAT INNER BELT ASSEMBLY(for Rear No. 2 Seat): REMOVAL+

18. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

2016 - 2020 MY Sienna [12/2015 -        ]; SEAT BELT: REAR NO. 2 SEAT INNER BELT ASSEMBLY(for LH Side): REMOVAL+

19. REMOVE NO. 2 SEAT CUSHION COVER WITH PAD LH

(a) Remove the 2 hog rings.

(b) Pass the 2 reclining remote control cable assemblies through the opening in the No. 2 seat cushion cover with pad LH and No. 2 seat cushion frame sub-assembly LH.

(c) Disengage the 6 hooks and remove the No. 2 seat cushion cover with pad LH.

20. REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH

(a) Remove the 5 hog rings and No. 2 seat cushion cover sub-assembly LH.

HINT:

Pull the straps of the No. 2 seat cushion cover sub-assembly LH through the openings in the No. 2 seat cushion pad LH.

21. REMOVE RECLINING REMOTE CONTROL CABLE ASSEMBLY

(a) Disconnect the 6 cable clamps and remove the reclining remote control cable assembly.

(b) Disconnect the 4 cable clamps and remove the reclining remote control cable assembly.

22. REMOVE REAR SEAT CUSHION

(a) Remove the 2 rear seat cushions.

23. REMOVE NO. 2 SEAT HINGE COVER

(a) Remove the 2 screws.

(b) Disengage the guide and remove the No. 2 seat hinge cover.