Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJSZ
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 11/2017]
Title: PRE-COLLISION: PRE-COLLISION SYSTEM: B2064; Vehicle Type Signal Malfunction; 2016 - 2017 MY Sienna [12/2015 - 11/2017]

DTC

B2064

Vehicle Type Signal Malfunction

DESCRIPTION

The seat belt control ECU is connected to the main body ECU using CAN communication.

The seat belt control ECU receives vehicle model information from the main body ECU and determines whether the seat belt buckle switch information from the center airbag sensor assembly is for the driver seat or the passenger seat.

DTC B2064 is stored when the CAN communication frame with the main body ECU is normal and communication is available, but the steering wheel position information is not set or varies.

DTC No.

DTC Detection Condition

Trouble Area

B2064

Communication with the main body ECU is normal and received steering wheel position information is not set (three times in succession).

  • CAN communication system
  • Main body ECU
  • Seat belt control ECU

CAUTION / NOTICE / HINT

HINT:

This circuit uses CAN communication. Therefore, be sure to check that the CAN communication system is normal before performing inspection (See page 2016 MY Sienna [12/2015 - 08/2016]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING ).

PROCEDURE

1.

CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

(a) Clear the DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING ).

(b) Check for DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING ).

OK:

CAN communication system DTC is not output.

NG

GO TO CAN COMMUNICATION SYSTEM

(See page 2016 MY Sienna [12/2015 - 08/2016]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING )

OK

2.

CHECK FOR DTC (PRE-COLLISION SYSTEM)

(a) Using the Techstream, enter the following menus: Body Electrical / Pre-Collision / Trouble Codes.

(b) Clear the DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR ).

(c) Check for DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR ).

OK:

DTC B2064 is not output.

OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION)

(See page 2016 MY Sienna [12/2015 - 08/2016]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING )

NG

3.

REPLACE MAIN BODY ECU

(a) Replace the main body ECU (See page 2016 - 2020 MY Sienna [12/2015 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL ).

NEXT

4.

CHECK FOR DTC (PRE-COLLISION SYSTEM)

(a) Using the Techstream, enter the following menus: Body Electrical / Pre-Collision / Trouble Codes.

(b) Clear the DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR ).

(c) Check for DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR ).

OK:

DTC B2064 is not output.

OK

END

NG

REPLACE SEAT BELT CONTROL ECU