Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJRH
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1698/82; Door Side Airbag Sensor LH Initialization Incomplete; 2016 - 2020 MY Sienna [12/2015 -        ]

DTC

B1698/82

Door Side Airbag Sensor LH Initialization Incomplete

DESCRIPTION

The circuit for the side collision sensor LH (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

The side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.

DTC B1698/82 is recorded when a malfunction is detected in the circuit for the side collision sensor LH (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No.

DTC Detection Condition

Trouble Area

B1698/82

When one of following conditions is met:

  • The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) for 2 seconds.
  • Side airbag sensor LH malfunction
  • Rear airbag sensor LH malfunction
  • Center airbag sensor assembly malfunction
  • Floor wire
  • Front door wire LH
  • Side airbag sensor LH
  • Rear airbag sensor LH
  • Center airbag sensor assembly

WIRING DIAGRAM

PROCEDURE

1.

CHECK PAST DTC

(a) Turn the ignition switch off.

(b) Turn the ignition switch to ON, and wait for at least 60 seconds.

(c) Check the past DTCs (See page 2016 - 2020 MY Sienna [12/2015 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: DTC CHECK / CLEAR ).

Result

Result

Proceed to

DTC B1692/81 is output

A

DTC B1697/82 is output

B

DTC B1692/81 and B1697/82 are not output

C

A

GO TO DTC B1692/81

B

GO TO DTC B1697/82

C

2.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the center airbag sensor assembly and side airbag sensor LH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

3.

CHECK CONNECTORS

(a) Disconnect the connectors from the center airbag sensor assembly and side airbag sensor LH.

(b) Check that the connectors (on the center airbag sensor assembly side and side airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.

NG

REPLACE HARNESS AND CONNECTOR

OK

4.

CHECK SIDE AIRBAG SENSOR LH CIRCUIT (CENTER AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR LH)

Text in Illustration

*1

Side Airbag Sensor LH

*2

Center Airbag Sensor Assembly

*3

Connector E

*4

Connector B

*5

Service Wire

-

-

*a

Rear view of wire harness connector

(to Side Airbag Sensor LH)

*b

Rear view of wire harness connector

(to Center Airbag Sensor Assembly)

(a) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

H12-4 (BBL+) - Body ground

Ignition switch ON

Below 1 V

H12-3 (BBL-) - Body ground

Ignition switch ON

Below 1 V

(d) Turn the ignition switch off.

(e) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(f) Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

H12-4 (BBL+) - H12-3 (BBL-)

Always

Below 1 Ω

(h) Disconnect the service wire from connector B.

(i) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

H12-4 (BBL+) - H12-3 (BBL-)

Always

1 MΩ or higher

H12-4 (BBL+) - Body ground

Always

1 MΩ or higher

H12-3 (BBL-) - Body ground

Always

1 MΩ or higher

NG

GO TO STEP 6

OK

5.

CHECK SIDE AIRBAG SENSOR LH

(a) Interchange the side airbag sensor LH with RH and connect the connectors to them.

(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON, and wait for at least 60 seconds.

(d) Clear the DTCs stored in the memory (See page 2016 - 2020 MY Sienna [12/2015 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: DTC CHECK / CLEAR ).

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON, and wait for at least 90 seconds.

(g) Check for DTCs (See page 2016 - 2020 MY Sienna [12/2015 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: DTC CHECK / CLEAR ).

Result

Result

Proceed to

DTC B1698/82 is output

A

DTC B1693/81 is output

B

DTC B1693/81 and B1698/82 are not output

C

Text in Illustration

*1

Side Airbag Sensor RH

*2

Center Airbag Sensor Assembly

HINT:

DTCs other than B1693/81 and B1698/82 may be output at this time, but they are not related to this check.

(h) Turn the ignition switch off.

(i) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(j) Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.

C

USE SIMULATION METHOD TO CHECK

A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B

REPLACE SIDE AIRBAG SENSOR LH

6.

CHECK FLOOR WIRE (CENTER AIRBAG SENSOR ASSEMBLY - FRONT DOOR WIRE LH)

Text in Illustration

*1

Side Airbag Sensor LH

*2

Center Airbag Sensor Assembly

*3

Front Door Wire LH

*4

Floor Wire

*5

Connector C

*6

Connector B

*7

Service Wire

-

-

*a

Front view of wire harness connector

(to Front Door Wire LH)

*b

Rear view of wire harness connector

(to Center Airbag Sensor Assembly)

(a) Disconnect the floor wire connector from the front door wire LH.

(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

HK1-1 (BBL-) - Body ground

Ignition switch ON

Below 1 V

HK1-3 (BBL+) - Body ground

Ignition switch ON

Below 1 V

(e) Turn the ignition switch off.

(f) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(g) Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

HK1-1 (BBL-) - HK1-3 (BBL+)

Always

Below 1 Ω

(i) Disconnect the service wire from connector B.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

HK1-1 (BBL-) - HK1-3 (BBL+)

Always

1 MΩ or higher

HK1-1 (BBL-) - Body ground

Always

1 MΩ or higher

HK1-3 (BBL+) - Body ground

Always

1 MΩ or higher

OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE