SUPPLEMENTAL RESTRAINT SYSTEMS: CURTAIN SHIELD AIRBAG ASSEMBLY: DISPOSAL; 2016 - 2020 MY Sienna [12/2015

Last Modified: 04-05-2023	6.11:8.1.0	Doc ID: RM100000000VJP9
Model Year Start: 2016	Model: Sienna	Prod Date Range: [12/2015 - ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CURTAIN SHIELD AIRBAG ASSEMBLY: DISPOSAL; 2016 - 2020 MY Sienna [12/2015 - ]

DISPOSAL

CAUTION / NOTICE / HINT

HINT:

Disposal procedure for the LH side is the same as that for the RH side.
The procedure described below is for the RH side.
When scrapping a vehicle equipped with the SRS or disposing of a curtain shield airbag assembly, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the TOYOTA MOTOR SALES, U.S.A., INC.

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.
Never dispose of a curtain shield airbag assembly that has an undeployed airbag.
The airbag emits an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.
When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the curtain shield airbag assembly.
The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a curtain shield airbag assembly which has been deployed.
Do not apply water, etc. to a curtain shield airbag assembly which has been deployed.
Always wash your hands with water after completing the operation.
An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

PROCEDURE

1. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)

HINT:

Prepare a battery as the power source to deploy the airbag.

(a) Check the function of SST (See page ).

SST: 09082-00700

(b) Read the precaution (See page ).

(d) Using a screwdriver with its tip wrapped in protective tape, release the locking button.

Text in Illustration

*a	Locking Button
*b	Protective Tape

(e) Using a screwdriver with its tip wrapped in protective tape, disconnect the airbag connector.

NOTICE:

Do not damage the airbag wire harness when handling the airbag connector.

(f) Connect SST.

Text in Illustration

*a	Locking Button

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

(1) Connect the SST connector to the curtain shield airbag assembly.

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.

(2) Close all doors.

NOTICE:

Do not damage the SST wire harness.

(3) Move SST to at least 10 m (32.8 ft.) away from the vehicle.

Text in Illustration

*a	Battery
*b	10 m or more

(4) Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

(g) Deploy the airbag.

(1) Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

(2) Press the SST activation switch and deploy the airbag.

CAUTION:

When deploying the airbag, make sure that no one is near the vehicle.
The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a curtain shield airbag assembly which has been deployed.
Do not apply water, etc. to a curtain shield airbag assembly which has been deployed.
Always wash your hands with water after completing the operation.

HINT:

The airbag is deployed as the LED on the SST activation switch illuminates.

2. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

HINT:

Prepare a battery as the power source to deploy the airbag.

(a) Check the function of SST (See page ).

SST: 09082-00700

(b) Remove the curtain shield airbag assembly (See page ).

Text in Illustration

Cut

(d) Connect SST.

Text in Illustration

*a	Locking Button

SST: 09082-00802

09082-10801

09082-20801

(1) Connect the SST connector to the curtain shield airbag assembly.

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.

(e) Using a braided wire harness, tie the curtain shield airbag assembly to a tire.

Text in Illustration

*a	Stripped Wire Section
*b	Wire Diameter

Wire:

Stripped wire section

1.25 mm² (0.0019 in.²) or more

CAUTION:

If the wire harness is too thin or an alternative object is used to tie the curtain shield airbag assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm² (0.0019 in.²).

HINT:

To calculate the area of the stripped wire harness cross section:

Area = 3.14 x (Diameter)² divided by 4

(1) Position the curtain shield airbag assembly inside the tire, as shown in the illustration.

Tire Size

Area	Measurement
A	185 mm (7.28 in.)
B	360 mm (14.17 in.)

CAUTION:

Make sure that the wire harnesses are tight. If there is any slack in the wire harnesses, the curtain shield airbag assembly may become loose due to the shock when the airbag is deployed.

NOTICE:

The tire will be marked by the airbag deployment, so use a waste tire.

(f) Place the tires.

Text in Illustration

*a	Tire (2 or more)

CAUTION:

Do not place the curtain shield airbag assembly with the deployment direction facing toward the ground.

(1) Place at least 2 tires under the tire to which the curtain shield airbag assembly is tied.

(2) Place at least 2 tires over the tire to which the curtain shield airbag assembly is tied. The disc wheel should be installed onto the top tire.

NOTICE:

Do not place the SST connector under the tire because it could be damaged.

(3) Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. It is highly dangerous when a loose wire harness results in the tires coming free due to the shock when the airbag is deployed.

(g) Connect SST.

(1) Connect the SST connector.

Text in Illustration

*1	Curtain Shield Airbag Assembly
*a	Battery
*b	10 m or more

SST: 09082-00700

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

(2) Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

(h) Deploy the airbag.

(1) Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

(2) Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the curtain shield airbag assembly is tied.

(3) Press the SST activation switch and deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.

HINT:

The airbag is deployed as the LED on the SST activation switch illuminates.

(i) Dispose of the curtain shield airbag assembly.

CAUTION:

The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a curtain shield airbag assembly which has been deployed.
Always wash your hands with water after completing the operation.
Do not apply water, etc. to a curtain shield airbag assembly which has been deployed.

(1) Remove the curtain shield airbag assembly from the tire.

(2) Place the curtain shield airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.