Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJLT
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2016]
Title: THEFT DETERRENT / KEYLESS ENTRY: ENGINE IMMOBILISER SYSTEM(w/ Smart Key System): REGISTRATION; 2016 MY Sienna [12/2015 - 08/2016]

REGISTRATION

PROCEDURE

1. DESCRIPTION OF CODE REGISTRATION

HINT:

  • The ID codes are the same as recognition codes for the wireless transmitter and the engine immobiliser function. Registering an ID code enables the smart key system, the wireless door lock control function and the engine immobiliser function to be operated.
  • Code registration is necessary when the certification ECU, steering lock ECU, or key is replaced with a new one.
  • This vehicle does not have a key slot. Therefore, touch the logo of the key to the engine switch when registering the key, as shown in the illustration.

2. KEY REGISTRATION PROCEDURES WHEN ADDING OR REPLACING KEY OR WHEN KEY IS LOST

HINT:

  • The following procedures require the use of the Techstream:
    • - New key ID registration
    • - Additional key ID registration
    • - Key ID erasure
    • - All key ID erasure*1
  • A maximum of 7 keys can be registered.

Customer Request/Condition

Registration Procedure Condition

Procedure

Refer to

Registering an additional key

Customer must bring at least 1 key

Register additional keys as necessary (additional key ID registration)

PROCEDURE "C"

  • Replacing a key
  • Making a lost key unusable

HINT:

After key ID erasure, any remaining keys that are not registered at this time cannot be used. Therefore, after key ID erasure, register all remaining keys.

Customer must bring at least 1 key

1. Using remaining key, clear all registered keys except one (key ID erasure)

PROCEDURE "D"

2. Register additional keys as necessary (additional key ID registration)

PROCEDURE "C"

All keys are lost*1

-

1. Reset all keys (all keys ID erasure (key code reset))

PROCEDURE "E"

2. Register all keys (new key ID registration)

PROCEDURE "A"

All keys are lost*2

-

1. Replace certification ECU

CERTIFICATION ECU / REMOVAL

2. Replace steering lock ECU

-

3. Register all keys (new key ID registration)

PROCEDURE "A"

4. Register ECU communication ID

PROCEDURE "F"

  • *1: except for GSL30L-PFTQKK, GSL35L-PFTQKK
  • *2: for GSL30L-PFTQKK, GSL35L-PFTQKK

3. PART REPLACEMENT AND KEY REGISTRATION PROCEDURES

(a) The following table shows ECU replacement and key registration procedures for cases in which a malfunctioning ECU has been identified through the troubleshooting of the smart key system.

HINT:

  • The following procedures can be performed:
    • New key ID registration
    • Additional key ID registration
    • Key ID erasure
    • All key ID erasure*1
      • *1: except for GSL30L-PFTQKK, GSL35L-PFTQKK
  • If the customer has not brought all the registered keys, replacement of the steering lock ECU is also required.
  • A maximum of 7 keys can be registered.

Malfunctioning ECU

Condition

Procedure

Reference

Certification ECU

Customer has brought all keys

1. Replace certification ECU

CERTIFICATION ECU / REMOVAL

2. Reregister all keys (New key ID registration)

PROCEDURE "B"

Some keys are lost

Key ID codes can be registered and erased

1. Erase key codes (Key ID erasure)

PROCEDURE "D"

2. Perform additional key registration procedure (Additional key ID registration)

PROCEDURE "C"

3. Replace certification ECU

CERTIFICATION ECU / REMOVAL

4. Reregister all keys (New key ID registration)

HINT:

If some keys are not registered during the above steps, they will be disabled because they cannot be registered later.

PROCEDURE "B"

Key ID codes cannot be either registered or erased

1. Replace certification ECU

CERTIFICATION ECU / REMOVAL

2. Replace steering lock ECU

-

3. Reregister all keys (New key ID registration)

HINT:

If key codes cannot be erased or additional keys cannot be registered due to a malfunction in the certification ECU, replace the steering lock ECU and certification ECU. If some keys are not registered during the above steps, they will be disabled because they cannot be registered later.

PROCEDURE "A"

4. Register ECU communication ID

PROCEDURE "F"

Certification ECU

All keys are lost

1. Replace certification ECU

CERTIFICATION ECU / REMOVAL

2. Replace steering lock ECU

-

3. Reregister all keys (New key ID registration)

HINT:

If key codes cannot be erased or additional keys cannot be registered due to a malfunction in the certification ECU, replace the steering lock ECU and certification ECU. If some keys are not registered during the above steps, they will be disabled because they cannot be registered later.

PROCEDURE "A"

4. Register ECU communication ID

PROCEDURE "F"

Steering lock ECU

Customer has brought at least 1 key

1. Replace steering lock ECU

-

2. Perform additional key registration procedure (Additional key ID registration)

PROCEDURE "C"

All keys are lost

1. Replace steering lock ECU

-

2. Replace certification ECU

CERTIFICATION ECU / REMOVAL

3. Reregister all keys (New key ID registration)

HINT:

If some keys are not registered during the above steps, they will be disabled because they cannot be registered later.

PROCEDURE "A"

4. Register ECU communication ID

PROCEDURE "F"

Power management control ECU

No condition required

Replace power management control ECU

-

ECM

No condition required

Replace ECM

-

4. KEY REGISTRATION

(a) PROCEDURE "A"

New key ID registration (when replacing the certification ECU and steering lock ECU)

Process

Procedure

1. Start of registration

  1. Connect the Techstream to DLC3
  2. Turn the engine switch on (IG)
  3. Enter the following menus: Body Electrical / Smart Key / Utility / Smart Code Registration

HINT:

The engine switch cannot be turned on (IG) more than 10 times. After connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at 1.5-second intervals or less to continue key registration procedure.

2. Confirmation of ECU code

  • Perform operation according to prompts on the Techstream screen

HINT:

Mode is automatically selected by the Techstream (new registration mode or add mode).

3. Verification of unregistered key*1

  1. Hold the unregistered key close to the engine switch (for details, refer to "Description of Code Registration")
  2. Confirm that the wireless door lock buzzer sounds once (short beep)
  3. Place the unregistered key on the driver seat
  4. Confirm that the wireless door lock buzzer sounds once (short beep)

4. Registration of ID code

  • Perform operation according to prompts on the Techstream screen

5. End of registration

  • Finish new key ID code registration
  • *1: Repeat this process for each key which is to be registered for the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys has not been finished within the specified time, perform the registration procedures again from process 1. Make sure that only 1 key is in the cabin during the registration procedures. If 2 or more keys are in the cabin simultaneously, electric waves will interfere with each other, preventing normal registration.

(b) PROCEDURE "B"

New key ID registration (when replacing the certification ECU)

Process

Procedure

1. Start of registration

  1. Connect the Techstream to DLC3
  2. Turn the engine switch on (IG)
  3. Enter the following menus: Body Electrical / Smart Key / Utility / Smart Code Registration

HINT:

The engine switch cannot be turned on (IG) more than 10 times. After connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at 1.5-second intervals or less to continue key registration procedure.

2. Confirmation of ECU code

  • Perform operation according to prompts on the Techstream screen

HINT:

Mode is automatically selected by the Techstream (new registration mode or add mode).

3. Confirmation of all registered keys*1

  1. Hold the registered key close to the engine switch (for details, refer to "Description of Code Registration")
  2. Confirm that wireless door lock buzzer sounds once (short beep)

4. Confirmation of ECU code

  • Perform operation according to prompts on the Techstream screen

5. Verification of unregistered key*2

  1. Hold the unregistered key close to the engine switch (for details, refer to "Description of Code Registration")
  2. Confirm that wireless door lock buzzer sounds once (short beep)
  3. Place the unregistered key on the driver seat
  4. Confirm that the wireless door lock buzzer sounds once (short beep)

6. Registration of ID code

  • Perform operation according to prompts on the Techstream screen

7. End of registration

  • Finish new key ID code registration
  • *1: Repeat this process for each key registered for the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys has not been finished within the specified time, perform the registration procedures again from process 1. If the key confirmation procedure for a key is performed, the security indicator light comes on and remains on until all the keys are confirmed.
  • *2: Repeat this process for each key which is to be registered for the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys is not finished within the specified time, perform the registration procedures again from process 1. Make sure that only 1 key is in the cabin during the registration procedures. If 2 or more keys are in the cabin simultaneously, electric waves will interfere with each other, preventing normal registration.

(c) PROCEDURE "C"

Additional key ID registration

Process

Procedure

1. Start of registration

  1. Connect the Techstream to DLC3
  2. Turn the engine switch on (IG)
  3. Enter the following menus: Body Electrical / Smart Key / Utility / Smart Code Registration

2. Confirmation of registered key*1

  1. Perform operation according to prompts on the Techstream screen

    HINT:

    Mode is automatically selected by the Techstream (new registration mode or add mode)

  2. Hold the registered key close to the engine switch (for details, refer to "Description of Code Registration")
  3. Confirm that the wireless door lock buzzer sounds once (short beep)

3. Confirmation of ECU code

  • Perform operation according to prompts on the Techstream screen

4. Verification of unregistered key*2

  1. Hold the unregistered key close to the engine switch (for details, refer to "Description of Code Registration")
  2. Confirm that the wireless door lock buzzer sounds once (short beep)
  3. Place the unregistered key on the driver seat
  4. Confirm that the wireless door lock buzzer sounds once (short beep)

5. Registration of ID code

  • Perform operation according to prompts on the Techstream screen

6. End of registration

  • Finish additional key ID code registration
  • *1: Perform this process for one of the keys registered for the vehicle. Finish the procedure within 30 seconds. If the procedure has not been finished within the specified time, perform the registration procedures again from process 1.
  • *2: Repeat this process for each key which is to be registered for the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys is not finished within the specified time, perform the registration procedures again from process 1. Make sure that only 1 key is in the cabin during the registration procedures. If 2 or more keys are in the cabin simultaneously, electric waves will interfere with each other, preventing normal registration.

(d) PROCEDURE "D"

Key ID erasure

HINT:

Procedure "D" erases all registered key codes except one.

Process

Procedure

1. Start of erasure

  1. Connect the Techstream to DLC3
  2. Turn the engine switch on (IG)
  3. Enter the following menus: Body Electrical / Smart Key / Utility / Smart Code Erasure

2. Confirmation of registered key*1

HINT:

Select the key that will not be erased.

  1. Perform operation according to prompts on the Techstream screen
  2. Hold the registered key close to engine switch (For details, refer to "Description of Code Registration")
  3. Confirm that the wireless door lock buzzer sounds once (short beep)

3. Confirmation of ECU code

  • Perform operation according to prompts on the Techstream screen

4. Erasure of ID code

  • Perform operation according to prompts on the Techstream screen

5. End of erasure

  • Finish key ID code erasure
  • *1: Perform this process for one of the keys registered for the vehicle. Finish the procedure within 30 seconds. If the procedure has not been finished within the specified time, perform the erasure procedures again from process 1.

(e) PROCEDURE "E"

All key ID erasure

HINT:

Procedure "E" erases all the key codes registered in the vehicle.

Process

Procedure

1. Start of erasure

  1. Connect the Techstream to DLC3
  2. Turn the engine switch on (IG)
  3. Turn the Techstream on while turning driver side door courtesy light switch on and off repeatedly at 1.5-second intervals or less
  4. Enter the following menus: Body Electrical / Smart Key / Utility / Smart Code Reset

2. Confirmation of ECU code

  • Perform operation according to prompts on the Techstream screen

3. Erasure of ID code

  • Perform operation according to prompts on the Techstream screen

4. End of erasure

  • Finish key ID code erasure

(f) PROCEDURE "F"

ECU communication ID registration

NOTICE:

  • The ECU communication ID should be registered when the certification ECU is replaced in order to match these ECU communication IDs.
  • The engine cannot be started unless the ECU communication IDs match.
  • After the registration, pressing the engine switch may not start the engine on the first try. If so, press the engine switch again.
  • Clear DTC B2799 (code for ECM immobiliser communication error) by either of the following:

    - Use the Techstream.

    - Disconnect the cable from the negative (-) battery terminal for 30 seconds.

(1) Using SST, connect terminals TC and CG of the DLC3.

SST: 09843-18040

(2) Turn the engine switch on (IG) and leave it as is for 30 minutes.

HINT:

Do not start the engine.

(3) Turn the engine switch off and disconnect terminals TC and CG.

(4) Check that the engine starts and stays running for more than 3 seconds.