Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJLS
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: ENGINE IMMOBILISER SYSTEM(w/ Smart Key System): DATA LIST / ACTIVE TEST; 2016 - 2020 MY Sienna [12/2015 -        ]

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Data List.

(e) Read the Data List according to the display on the Techstream.

Smart Key

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Ignition Switch

Engine switch on (IG) signal/ON or OFF

ON: Engine switch on (ACC, IG) or engine started

OFF: Engine switch off

-

Immobilizer when IG=ON

Immobiliser system status when Engine Switch on (IG) / Set or Unset

Set: Key not in cabin

Unset: Key in cabin when Engine Switch on (IG)

-

# Codes

Number of trouble codes/Min.: 0 or Max.: 255

Number of DTCs will be displayed

-

Immobiliser

Immobiliser system status/Set or Unset

Set: Key not in cabin

Unset: Key in cabin

-

Master Key

Master key code signal/Match or NoMatch

Match: Master key code sent

NoMatch: Unmatched master key code sent

-

Sub Key

Sub-key (Master key) code signal/Match or NoMatch

Match: Sub-key (master key) code sent

NoMatch: Unmatched sub-key (master key) code sent

-

BCC Malfunction

Transponder chip signal/OK or NG

OK: Correct data sent

NG: Incorrect data sent

-

Abnormal Status

Transponder chip data/OK or NG

OK: Data OK

NG: Data error

-

Different Encrypt Code

Transponder chip signal/OK or NG

OK: Correct data sent

NG: Incorrect data sent

-

Different Serial Number

Transponder chip signal/OK or NG

OK: Correct data sent

NG: Incorrect data sent

-

Frame Error

Transponder chip signal/OK or NG

OK: Correct data sent

NG: Incorrect data sent

-

Response

Transponder chip signal/OK or NG

OK: Correct data sent

NG: Incorrect data sent

-

Wireless Starter Com ID

Wireless starter communication ID / No Regd or Regd

No Regd: Wireless C code not registered

Regd: Wireless C code registered

-

Wireless C Code

Wireless C code / No Regd or Regd

No Regd: Wireless C code not registered

Regd: Wireless C code registered

-

ID-BOX Sleep Condition

ID code box condition/Yes or No

Yes: ID code box in sleep condition

No: ID code box not in sleep condition

-

ID-BOX Start Condition

ID code box condition/Yes or No

Yes: ID code box sends wake up signal

No: ID code box does not send wake up signal

-

Engine Start Request

Certification ECU start request condition/OK or NG

OK: Start request condition signal received (past)

NG: Start request condition signal not received (past)

-

3bit Code Request

3-bit code request condition / OK or NG

OK: 3-bit code request condition signal received (past)

NG: 3-bit code request condition signal not received (past)

-

S Code Check

S code verification result/OK or NG

OK: Verification confirmed

NG: Verification not confirmed

-

L Code Check

L code verification result/OK or NG

OK: Verification confirmed

NG: Verification not confirmed

-

Unlock Request Receive

Steering unlock command reception status/OK or NG

OK: Steering unlock request received

NG: Steering unlock request not received

-

Lock Request Receive

Steering lock command reception status/OK or NG

OK: Steering lock request received

NG: Steering lock request not received

-

S Code Check (Past)

S code verification result (past)/OK or NG(Past)

OK: Verification confirmed (past)

NG(Past): Verification not confirmed (past)

-

L Code Check (Past)

L code verification result (past)/OK or NG(Past)

OK: Verification confirmed (past)

NG(Past): Verification not confirmed (past)

-

EFI Code Receive

SFI code receive (when DTC stored)/OK or NG

OK: SFI code received

NG: SFI code not received

-

EFI Communication

SFI communication/OK or NG

OK: SFI communication normal

NG: SFI communication abnormal

-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Smart Key

Tester Display

Test Part

Control Range

Diagnostic Note

Immobiliser Indicator

Immobiliser Indicator light

ON or OFF

-