Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000000VJL9 |
Model Year Start: 2016 |
Model: Sienna |
Prod Date Range: [12/2015 -
] |
Title: THEFT DETERRENT / KEYLESS ENTRY: ENGINE IMMOBILISER SYSTEM(w/o Smart Key System): REGISTRATION; 2016 - 2020 MY Sienna [12/2015 - ] |
REGISTRATION
PROCEDURE
1. DESCRIPTION OF CODE REGISTRATION
HINT:
The key has 2 codes: the key code (immobiliser code) and the wireless code. Both of these codes need to be registered. For the wireless code registration procedures, refer to Wireless Door Lock Control System (See page
).
(a) When adding master keys or sub keys (Additional registration):
(1) Register the key code (immobiliser code) in the transponder key ECU.
Target ECU
|
Refer to
|
Transponder key ECU
|
Procedure "B"
|
(b) When replacing the transponder key ECU (New registration):
(1) Register the key code (immobiliser code) in the new transponder key ECU.
Target ECU
|
Refer to
|
Transponder key ECU
|
Procedure "A"
|
(2) Register the ECU communication ID between the new transponder key ECU and the ECM.
Target ECU
|
Refer to
|
ECM
|
Procedure "E"
|
(c) When replacing the ECM:
(1) Register the ECU communication ID between the transponder key ECU and the new ECM.
Target ECU
|
Refer to
|
Transponder key ECU
|
Procedure "F"
|
(d) When replacing the transponder key ECU and the ECM:
(1) Register the key codes (immobiliser codes) in the new transponder key ECU.
Target ECU
|
Refer to
|
Transponder key ECU
|
Procedure "A"
|
(2) Register the ECU communication ID between the new transponder key ECU and the new ECM.
Target ECU
|
Refer to
|
Transponder key ECU
|
Procedure "F"
|
(e) When erasing key codes:
(1) Erasing all of the key codes except the master key.
Target ECU
|
Refer to
|
Transponder key ECU
|
Procedure "C"
|
(2) Erasing all of the key codes.
Target ECU
|
Refer to
|
Transponder key ECU
|
Procedure "D"
|
2. KEY REGISTRATION
(a) New key code registration (Procedure "A"):
NOTICE:
Make sure that no key codes are registered in the transponder key ECU.
HINT:
-
In this mode, a maximum of 3 key codes for 2 master keys and 1 sub-key can be registered. The master keys and sub-key can be registered in any order because the transponder key ECU can distinguish between different types of keys.
-
New key codes must be registered with the battery connected. The ignition switch can be either ON or off.
-
When a new transponder key ECU is installed, key codes must be registered in the transponder key ECU assembly.
Automatic Key Code Registration (New Registration)
Procedure
|
Security Indicator Light Condition
|
1. Start
|
Blinking
HINT:
Until first key is inserted
|
2. Insert the master key into the ignition key cylinder.
|
Blinking
|
3. Techstream operation
Enter the following menus: Body Electrical / Immobiliser / Utility / Key Registration
HINT:
After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen.
|
OFF for 1 second and then ON
|
4. Remove the key and then select Next on the Techstream.
|
ON
|
5. Insert the master key to be registered and then select Next on the Techstream.
|
OFF for 1 second and then ON
|
6. Remove the key and then select Next on the Techstream.
|
ON
|
7. Insert the sub-key to be registered and then select Next on the Techstream.
|
OFF for 1 second and then ON for 0.5 seconds and then OFF
|
8. Remove the key.
|
Blinking
|
9. End (Procedure "E")
|
HINT:
-
When the engine immobiliser system is operating normally and the key is pulled out, the security indicator light blinks continuously.
-
If the new key code registration fails, code 2-1 will be output through the security indicator light. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The output details are shown below.
(b) Finish the automatic key code registration mode. The automatic key code registration mode can be forced to end when at least 1 key code (immobiliser code) for the master key has been registered.
HINT:
Follow the instruction on the Techstream screen to end new key code registration mode.
3. REGISTRATION OF ADDITIONAL KEY
(a) Additional registration (Procedure "B"):
HINT:
-
A maximum of 5 key codes and 3 sub-key codes can be registered.
-
Registration mode will end if any step is not completed within the specified time.
-
When the ignition cylinder or the key cylinder set is replaced, remove the transmitter module from the original master key. Then install this transmitter module to a new key and use the new key as the master key. If necessary, use this master key to register other keys.
NOTICE:
When the ignition key cylinder has been replaced, locking and unlocking doors are possible with the new master key's transmitter module (removed from the original master key). However, the new master key will not be able to lock and unlock doors through the door key cylinder. Keep the original master key. If the battery in the new master key's transmitter module fails, the original master key can be used to lock and unlock doors through the door key cylinder.
Additional Registration
Procedure
|
Time to Complete Operation
|
Security Indicator Light Condition
|
1. Start
|
-
|
Blinking
HINT:
Until first key is inserted
|
2. Insert the already registered master key into the ignition key cylinder and turn the ignition switch to ON.
|
-
|
OFF
|
3. Techstream operation
Enter the following menus: Body Electrical / Immobiliser / Utility / Key Registration
HINT:
After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen.
|
Within 120 sec.
|
ON
|
4. Remove the master key.
|
Within 20 sec.
HINT:
After the Techstream instruction
|
ON
|
5. Insert the key to be registered in the ignition key cylinder.
|
Within 10 sec.
|
Blinking
|
6. Wait for 60 sec. after the key is registered.
HINT:
The security indicator light goes off.
|
-
|
OFF
|
7. Remove the key.
|
-
|
Blinking
|
8. End
|
HINT:
-
A brief outline of a key code registration procedure is shown above. For detailed information, refer to the Techstream screen.
-
When the engine immobiliser system is operating normally and the key is pulled out, the security indicator light blinks continuously.
-
If the key code registration has failed in automatic key code registration mode, code 2-1 will be output through the security indicator light. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The details are shown in procedure "A".
4. ERASURE OF KEY CODE
(a) Key code erasure (Procedure "C"):
HINT:
-
Performing this procedure will erase all key codes except for the master key, which is used for erasing the key codes. In order to use a key whose code has been erased, a new key code must be registered.
-
This procedure will be canceled if each step is not completed within the specified time.
Key Code Erasure
Procedure
|
Time to Complete Operation
|
Security Indicator Light Condition
|
1. Start
|
-
|
Blinking
HINT:
Until first key is inserted
|
2. Insert the already registered master key in the ignition key cylinder and turn the ignition switch to ON.
|
-
|
OFF
|
3. Techstream operation
Enter the following menus: Body Electrical / Immobiliser / Utility / Transponder Code Erasure
HINT:
After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen.
|
Within 120 sec.
|
ON for 1 sec. then OFF
|
4. Remove the master key.
|
Within 10 sec.
HINT:
After the Techstream instruction
|
ON
|
5. End
|
HINT:
-
A brief outline of a key code registration procedure is shown above. For detailed information, refer to the Techstream screen.
-
When the engine immobiliser system is operating normally and the key is pulled out, the security indicator light blinks continuously.
(b) All key code erasure (Procedure "D"):
HINT:
-
To perform this procedure, at least 1 key should have been registered to the transponder key ECU.
-
This procedure can be performed using either a registered or unregistered key.
All Key Code Erasure
Procedure
|
Time to Complete Operation
|
Security Indicator Light Condition
|
1. Start
|
-
|
Blinking
|
2. Insert previously registered master key or unregistered key into ignition key cylinder and turn ignition switch to ON.
|
Within 10 min.
|
ON or OFF
|
3. Using TIS, confirm that user and vehicle match.
|
4. Techstream operation
Enter the following menus: Body Electrical / Immobiliser / Utility / Transponder Code Erasure
HINT:
After completing the above operation, proceed to the next step in accordance with the prompts on the Techstream screen.
|
Within 15 min.
|
ON for 1 sec. then OFF
|
5. Completion of erasure of all key codes is displayed.
|
Within 10 sec.
HINT:
After the Techstream instruction
|
ON
|
6. End
|
HINT:
-
A brief outline of a key code registration procedure is shown above. For detailed information, refer to the Techstream screen.
-
When the engine immobiliser system is operating normally and the key is pulled out, the security indicator light blinks continuously.
5. ECU COMMUNICATION ID REGISTRATION
(a) ECU communication ID registration (Procedure "E"):
(1) Using SST, connect terminals TC and CG of the DLC3.
SST: 09843-18040
(2) Turn the ignition switch to ON and leave the vehicle as is for 30 minutes.
HINT:
Do not start the engine.
(3) Check that the engine starts.
(b) ECU communication ID registration (Procedure "F"):
NOTICE:
The ECU communication ID should be registered when the ECM and transponder key ECU are replaced or when the ECM only is replaced in order to match the ECU communication ID.
ECU Communication ID Registration
Procedure
|
Security Indicator Light Condition
|
1. Start
|
OFF
|
2. Insert an already registered key into the ignition key cylinder.
|
3. Start the engine.
|
4. Check that the engine starts and stays on for more than 3 seconds.
|
5. End
|
|