OPERATION CHECK

1. SMART KEY SYSTEM OPERATION INSPECTION

(a) Check the entry unlock function.

(1) Use the wireless lock operation to lock the doors. With the key outside the vehicle, touch a front door outside handle assembly (touch sensor) and check that the door unlocks.

(b) Check the entry unlock operation detection area.

(1) Step 1: Hold the key at the same height as the door outside handle assembly (approximately 0.8 m (2.62 ft.)). Make sure that the direction of the key is as shown in the illustration.

(2) Step 2: Check that when the key is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the vehicle, the system enters unlock standby mode.

Text in Illustration

HINT:

When the system enters unlock standby mode, the key LED illuminates.

(3) Step 3: After the system enters unlock standby mode, touch the door outside handle assembly (touch sensor) within 3 seconds. Check that the door unlocks.

NOTICE:

The key may not be able to communicate with the system within a 0.2 m (0.656 ft.) radius of each door outside handle assembly.

(4) Step 4: Repeat step 2 and 3 for the remaining front door.

(5) Step 5: Inspect the door outside handle assembly (touch sensor) response sensitivity. When the system is in unlock standby mode, check that touching the area shown in the illustration causes the door to unlock.

NOTICE:

When touching the highlighted area, touching too quickly or having extended contact may not trigger the sensor. In such a case, the door will not unlock.

(6) Step 6: Repeat step 5 for the remaining front door.

(c) Check the entry lock function.

NOTICE:

If the key is in the cabin, but is not in a detection area (on the instrument panel, rear tray, in the glove box, or on the floor), the key confinement function may not operate. This can result in the key confinement.

(1) Step 1: Confirm that all the doors lock when a lock sensor on a front door outside handle is touched with all the doors closed and unlocked while the key is outside of the vehicle.

(2) Step 2: Inspect the smart door lock detection area. Hold the key 0.1 m (0.328 ft.) below the window (about 1 m (3.28 ft.) above the ground). Move the key about 0.3 m (0.984 ft.) away from the vehicle and touch the lock sensor as shown in the illustration to check that all doors lock.

Text in Illustration

(d) Check the entry back door open function.

(1) Close the back door. With the key outside the vehicle, check that pushing the back door opener switch assembly opens the back door.

(2) Inspect the entry back door open operation detection area. Hold the key at the same height as the back door opener switch assembly (approximately 0.8 m (2.62 ft.)) aligning it with the center of the rear of the vehicle. Make sure that the direction of the key is as shown in the illustration. Check that when the key is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the vehicle, pushing the back door opener switch assembly opens the back door.

Text in Illustration

(e) Check the entry back door lock function.

(1) Close all of the vehicle doors. With the key in your possession outside of the vehicle, check that pushing the back door opener switch assembly (lock switch) locks all the doors.

Text in Illustration

(f) Check the smart power slide door open function.

(1) Confirm that the power slide door operation requirements are met. Refer to power slide door system.

(2) Use the wireless lock operation to lock the doors. With the key inside the detection area formed by the outside electrical key oscillator (for driver and front passenger side), pulling on the rear door outside handle for approximately 1 second will cause all doors to unlock and the activated power slide door to open automatically.

HINT:

The smart power slide door open function uses the detection area formed by the outside electrical key oscillator (for driver and front passenger side).

(g) Check the entry ignition function.

(1) While holding the key, confirm that the engine switch indicator light illuminates green when the engine switch is off, the shift lever is in P and the brake pedal is depressed. With the engine switch indicator illuminates green, confirm that the engine starts when the engine switch is pressed.

(2) While holding the key, confirm that the engine switch turns off → on (ACC) → on (IG) → off every time the engine switch is pressed when the brake pedal is not depressed.

HINT:

When the engine switch is pressed with the engine switch on (IG) and the shift lever is in any position except P, the engine switch will not turn off but remain on (ACC).

(3) With the engine running, vehicle stopped and shift lever in P, confirm that pressing the engine switch turns the engine off, and that the steering lock engages after opening the driver door.

HINT:

When the engine switch is pressed with the engine switch on (IG) and the shift lever in any position except P, the engine switch will not turn off but remain on (ACC).

(4) Inspect the detection area for the entry ignition function (for front floor). Make sure that the direction of the key is as shown in the illustration. When the key is in either of the 2 inspection points shown in the illustration, check that the engine can start.

Text in Illustration

NOTICE:

The engine may not start when the key is on the instrument panel, rear package tray or in the glove box.

(5) Inspect the detection area for the entry ignition function (for center floor). Make sure that the direction of the key is as shown in the illustration. When the key is in either of the 2 inspection points shown in the illustration, check that the engine can start.

Text in Illustration

NOTICE:

The engine may not start when the key is on the instrument panel, rear package tray or in the glove box.

(6) Inspect the detection area for the entry ignition function (for rear floor). Make sure that the direction of the key is as shown in the illustration. When the key is in either of the 2 inspection points shown in the illustration, check that the engine can start.

Text in Illustration

NOTICE:

The engine may not start when the key is on the instrument panel, rear package tray or in the glove box.

(h) Check the key confinement prevention function (in cabin)

NOTICE:

Perform this check with a window open to prevent key confinement.

(1) Turn the engine switch off.

(2) Put the key on a front seat or a rear seat.

(3) Close all the doors (all doors are in unlocked state).

(4) Confirm that the door lock does not operate but the wireless door lock buzzer sounds for 10 seconds when a front door lock sensor is touched.

(i) Check the key cancel function.

(1) While the engine switch is on (IG), check that the back door opener switch assembly (opener switch) is the only switch that can be operated in the smart key system.

(2) While the key cancel function (smart key system cancel function) is on, check that all functions of the smart key system cannot be operated.

(j) Check the answer-back function (hazard warning light flashing and buzzer sounding).

(k) Check that the key reminder warning buzzer sounds.

(1) With the key inside the vehicle, close the driver door. Then turn the engine switch off or on (ACC).

(2) Open the driver door and check that the buzzer sounds intermittently.

(l) Check that the key reminder warning buzzer stops.

(1) When the buzzer is sounding, check that the buzzer stops sounding if either of the following is performed:

2. KEY DIAGNOSTIC MODE

HINT:

Key diagnostic mode checks if the key within a selected oscillator detection area is operating normally. The results are output through the wireless door lock buzzer.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Key Communication Check.

(e) Check the values by referring to the table below.

Smart Key (Certification ECU (Smart Key ECU Assembly))

(f) When the key is brought near the selected oscillator, check that the wireless door lock buzzer sounds.

(1) *1: Door electrical key oscillator (for driver side)

Text in Illustration

(2) *3: Indoor electrical key oscillator (for front floor)

Text in Illustration

HINT:

Place the key on the driver or front passenger seat cushion.

(3) *4: Indoor electrical key oscillator (for center floor)

Text in Illustration

HINT:

Place the key on the rear No. 1 seat cushion.

(4) *5: Indoor electrical key oscillator (for rear floor)

Text in Illustration

HINT:

Place the key on the luggage area.

(5) *6: Outside electrical key oscillator (for rear side)

Text in Illustration

HINT:

Hold the key at the same height as the rear bumper upper surface and align with the center of the rear of the vehicle, as shown in the illustration.