Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJJN
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2016]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): Power Source Mode does not Change to ON (IG); 2016 MY Sienna [12/2015 - 08/2016]

Power Source Mode does not Change to ON (IG)

DESCRIPTION

When the engine switch is pushed with the key in the cabin, the power management control ECU receives signals to switch the power source mode.

Use this troubleshooting procedure when the power source mode does not change to on (IG) but does change to on (ACC).

HINT:

  • When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).
  • When the battery cable is disconnected and reconnected, the power source mode returns to the mode it was in before the battery cable was disconnected.

WIRING DIAGRAM

Refer to "Power Source Mode does not Change to on (IG and ACC)" (See page 2016 MY Sienna [12/2015 - 08/2016]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): Power Source Mode does not Change to ON (IG and ACC)+ ).

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and vehicle begins, or 2) connect the Techstream to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body Electrical / Smart Key / Trouble Codes.
  • Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page 2016 MY Sienna [12/2015 - 08/2016]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): DIAGNOSTIC TROUBLE CODE CHART ).
  • The smart key system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting( 2016 MY Sienna [12/2015 - 08/2016]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING ).
  • If the smart key is disabled through the customize function, enable the system before performing troubleshooting (See page 2016 - 2020 MY Sienna [12/2015 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): CUSTOMIZE PARAMETERS ).
  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  • After completing repairs, confirm that the problem does not occur.

Related Data List and Active Test Items

Problem Symptom

Data List Item

Active Test Item

Power source mode does not change to on (IG) but does change to on (ACC)

Power Source Control

  • Power Supply Condition
  • IG1 Relay Monitor(Inside)
  • IG2 Relay Monitor(Inside)
  • IG1 Relay Monitor(Outside)
  • IG2 Relay Monitor(Outside)
  • Latch Circuit
  • IG1 Circuit
  • IG2 Circuit

Starting Control

  • Ignition

-

PROCEDURE

1.

CHECK DTC (ALL)

2016 MY Sienna [12/2015 - 08/2016]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): Power Source Mode does not Change to ON (IG and ACC)+

NG

GO TO DTC CHART

OK

2.

CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

(a) Disconnect the D89 power management control ECU connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

D89-1 (AM22) - Body ground

Always

9.5 to 14 V

Text in Illustration

*a

Rear view of wire harness connector

(to Power Management Control ECU)
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK

3.

INSPECT IG2 RELAY

(a) Remove the IG2 relay from the engine room relay block.

(b) Inspect IG2 relay (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): RELAY: ON-VEHICLE INSPECTION ).

NG

REPLACE IG2 RELAY
OK

4.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2, IG1 NO. 3 AND IG1 NO. 4 RELAYS)

(a) Disconnect the 2A and 2D instrument panel junction block assembly connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2A-16 - 2D-7

20°C (68°F)

50.63 to 123.75 Ω

Text in Illustration

*a

Component without harness connected

(Instrument Panel Junction Block Assembly)
NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

5.

CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the D89 power management control ECU connector.

(b) Disconnect the 2A instrument panel block assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D89-20 (IG1D) - 2A-16

Always

Below 1 Ω

D89-20 (IG1D) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

6.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

(a) Disconnect the 2D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2D-7 - Body ground

Always

Below 1 Ω
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

7.

CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - IG2 RELAY)

(a) Disconnect the A35 power management control ECU connector.

(b) Remove the IG2 relay from the engine room relay block.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A35-8 (IG2D) - 1 (IG2 relay terminal)

Always

Below 1 Ω

A35-8 (IG2D) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

8.

CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)

(a) Remove the IG2 relay from the engine room relay block.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2 (IG2 relay terminal) - Body ground

Always

Below 1 Ω

Text in Illustration

*a

Component without relay connected

(IG2 Relay Terminal)
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

9.

INSPECT POWER MANAGEMENT CONTROL ECU

2016 - 2020 MY Sienna [12/2015 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): B2271; Ignition Hold Monitor Malfunction+

NG

REPLACE POWER MANAGEMENT CONTROL ECU

OK

10.

CONFIRMATION TEST

2016 MY Sienna [12/2015 - 08/2016]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): Power Source Mode does not Change to ON (IG and ACC)+

OK

SYSTEM RETURNED TO NORMAL (PROBLEM OCCURRED DUE TO BAD CONNECTION, BUT RETURNED TO NORMAL BY RECONNECTING CONNECTOR)
NG

CHECK RELAY CONTACT CIRCUIT