Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJJH
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): B2274; ACC Monitor Malfunction; 2016 - 2020 MY Sienna [12/2015 -        ]

DTC

B2274

ACC Monitor Malfunction

DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit between the ACC output terminal of the power management control ECU and the ACC relay is detected.

HINT:

  • When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).
  • When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.

DTC Code

DTC Detection Condition

Trouble Area

DTC Output Confirmation Operation

B2274

Malfunction in the ACC relay activation circuit in the power management control ECU or the external circuit (1-trip detection logic*).

HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.

  • AM2 No.2 fuse
  • Instrument panel junction block assembly (ACC relay)
  • Power management control ECU
  • Harness or connector

Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.

HINT:

To turn the engine switch on (ACC), carry the key and press the engine switch with the shift lever in P and the brake pedal released.

  • *: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Function when Malfunction Detected

  • If there is a malfunction when the relay is stuck on, the ACC relay does not turn off even though all the power is off.
  • If there is a malfunction when the relay is off, the ACC relay does not turn on even though the power source mode is on (ACC).

HINT:

The power source can change to on (IG) and the engine can be started.

-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and vehicle begins, or 2) connect the Techstream to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body Electrical / Smart Key / Trouble Codes.
  • The smart key system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page 2016 MY Sienna [12/2015 - 08/2016]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING 2018 - 2020 MY Sienna [11/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING ).
  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  • When the power source mode cannot change to on (ACC), the audio and navigation systems do not operate.
  • After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

Related Data List and Active Test Items

DTC

Data List Item

Active Test Item

B2274

Power Source Control

  • ACC Relay Monitor

Starting Control

  • Ignition

-

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

2016 - 2020 MY Sienna [12/2015 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): B2271; Ignition Hold Monitor Malfunction+

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

OK

2.

CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

2016 - 2020 MY Sienna [12/2015 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM(for Start Function): B2271; Ignition Hold Monitor Malfunction+

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

(a) Disconnect the 2A and 2D instrument panel junction block assembly connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2A-17 - 2D-5

20°C (68°F)

50.63 to 123.75 Ω

Text in Illustration

*a

Component without harness connected

(instrument panel Junction Block Assembly)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK

4.

CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 2A and 2D instrument panel junction block assembly connectors.

(b) Disconnect the D89 power management control ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D89-19 (ACCD) - 2A-17

Always

Below 1 Ω

2D-5 - Body ground

Always

Below 1 Ω

D89-19 (ACCD) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

INSPECT POWER MANAGEMENT CONTROL ECU

(a) Connect the power management control ECU connectors.

Text in Illustration

*a

Component with harness connected

(Power Management Control ECU)

-

-

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D89-19 (ACCD) - Body ground

Engine switch off

1 V or less

Engine switch on (ACC)

8.5 V or higher

OK

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

NG

REPLACE POWER MANAGEMENT CONTROL ECU

(See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; POWER DISTRIBUTION: POWER MANAGEMENT CONTROL ECU: REMOVAL 2018 - 2020 MY Sienna [11/2017 -        ]; POWER DISTRIBUTION: POWER MANAGEMENT CONTROL ECU: REMOVAL )