Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJFT
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: DOOR LOCK: SLIDE DOOR LOCK: INSPECTION; 2016 - 2020 MY Sienna [12/2015 -        ]

INSPECTION

PROCEDURE

1. INSPECT SLIDE DOOR HANDLE ASSEMBLY LH (w/o Power Slide Door)

(a) Apply battery voltage to the motor terminals and check the operation of the slide door handle.

Text in Illustration

*a

Component without harness connected

(slide door handle LH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 2 (L)

Battery negative (-) → 3 (UL)

Locks

Battery positive (+) → 3 (UL)

Battery negative (-) → 2 (L)

Unlocks

If the result is not as specified, replace the slide door handle.

(b) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (LSSR) - 4 (E)

Locked

10 kΩ or higher

1 (LSSR) - 4 (E)

Unlocked

Below 1 Ω

If the result is not as specified, replace the slide door handle.

2. INSPECT SLIDE DOOR HANDLE ASSEMBLY LH (w/ Power Slide Door)

(a) Apply battery voltage to the motor terminals and check the operation of the slide door handle.

Text in Illustration

*a

Component without harness connected

(slide door handle LH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 2 (L)

Battery negative (-) → 3 (UL)

Locks

Battery positive (+) → 3 (UL)

Battery negative (-) → 2 (L)

Unlocks

If the result is not as specified, replace the slide door handle.

(b) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (LSSR) - 4 (E)

Locked

10 kΩ or higher

1 (LSSR) - 4 (E)

Unlocked

Below 1 Ω

If the result is not as specified, replace the slide door handle.

(c) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (GND) - 4 (DS2)

Inner Handle Pulled

Below 1 Ω

1 (GND) - 3 (DS1)

1 (GND) - 4 (DS2)

Inner Handle not Pulled

10 kΩ or higher

1 (GND) - 3 (DS1)

If the result is not as specified, replace the slide door handle.

3. INSPECT SLIDE DOOR HANDLE ASSEMBLY LH (w/ Smart Key System)

(a) Apply battery voltage to the motor terminals and check the operation of the slide door handle.

Text in Illustration

*a

Component without harness connected

(slide door handle LH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 2 (L)

Battery negative (-) → 3 (UL)

Locks

Battery positive (+) → 3 (UL)

Battery negative (-) → 2 (L)

Unlocks

If the result is not as specified, replace the slide door handle.

(b) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (LSSR) - 4 (E)

Locked

10 kΩ or higher

1 (LSSR) - 4 (E)

Unlocked

Below 1 Ω

If the result is not as specified, replace the slide door handle.

(c) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (GND) - 6 (DS1)

Inner Handle Pulled

Below 1 Ω

1 (GND) - 7 (DS2)

5 (GND) - 10 (SW)

1 (GND) - 6 (DS1)

Inner Handle not Pulled

10 kΩ or higher

1 (GND) - 7 (DS2)

5 (GND) - 10 (SW)

If the result is not as specified, replace the slide door handle.

4. INSPECT SLIDE DOOR HANDLE ASSEMBLY RH (w/o Power Slide Door)

(a) Apply battery voltage to the motor terminals and check the operation of the slide door handle.

Text in Illustration

*a

Component without harness connected

(slide door handle RH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 2 (L)

Battery negative (-) → 3 (UL)

Locks

Battery positive (+) → 3 (UL)

Battery negative (-) → 2 (L)

Unlocks

If the result is not as specified, replace the slide door handle.

(b) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (LSSR) - 4 (E)

Locked

10 kΩ or higher

1 (LSSR) - 4 (E)

Unlocked

Below 1 Ω

If the result is not as specified, replace the slide door handle.

5. INSPECT SLIDE DOOR HANDLE ASSEMBLY RH (w/ Power Slide Door)

(a) Apply battery voltage to the motor terminals and check the operation of the door lock motor.

Text in Illustration

*a

Component without harness connected

(slide door handle RH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 2 (L)

Battery negative (-) → 3 (UL)

Locks

Battery positive (+) → 3 (UL)

Battery negative (-) → 2 (L)

Unlocks

If the result is not as specified, replace the slide door handle.

(b) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (LSSR) - 4 (E)

Locked

10 kΩ or higher

1 (LSSR) - 4 (E)

Unlocked

Below 1 Ω

If the result is not as specified, replace the slide door handle.

(c) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (GND) - 4 (DS2)

Inner Handle Pulled

Below 1 Ω

1 (GND) - 3 (DS1)

1 (GND) - 4 (DS2)

Inner Handle not Pulled

10 kΩ or higher

1 (GND) - 3 (DS1)

If the result is not as specified, replace the slide door handle.

6. INSPECT SLIDE DOOR HANDLE ASSEMBLY RH (w/ Smart Key System)

(a) Apply battery voltage to the motor terminals and check the operation of the door lock motor.

Text in Illustration

*a

Component without harness connected

(slide door handle RH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 2 (L)

Battery negative (-) → 3 (UL)

Locks

Battery positive (+) → 3 (UL)

Battery negative (-) → 2 (L)

Unlocks

If the result is not as specified, replace the slide door handle.

(b) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (LSSR) - 4 (E)

Locked

10 kΩ or higher

1 (LSSR) - 4 (E)

Unlocked

Below 1 Ω

If the result is not as specified, replace the slide door handle.

(c) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (GND) - 6 (DS1)

Inner Handle Pulled

Below 1 Ω

1 (GND) - 7 (DS2)

5 (GND) - 10 (SW)

1 (GND) - 6 (DS1)

Inner Handle not Pulled

10 kΩ or higher

1 (GND) - 7 (DS2)

5 (GND) - 10 (SW)

If the result is not as specified, replace the slide door handle.

7. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY LH

(a) Check the operation of the slide door closer motor.

Text in Illustration

*a

Component without harness connected

(Power Slide Door Lock Assembly LH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 1 (ACT+)

Battery negative (-) → 4 (ACT-)

Close rotation

Battery positive (+) → 4 (ACT-)

Battery negative (-) → 1 (ACT+)

Release rotation

If the result is not as specified, replace the power slide door lock.

(b) Measure the resistance according to the values in the table below.

Text in Illustration

*a

Component without harness connected

(Power Slide Door Lock Assembly LH)

Standard Resistance:

Full Latch Switch

Tester Connection

Condition

Specified Condition

6 (FUL) - 7 (E1)

Open

Below 1 Ω

Half latch

Full latch

10 kΩ or higher

Over latch

Half Latch Switch

Tester Connection

Condition

Specified Condition

5 (HAF) - 7 (E1)

Open

Below 1 Ω

Full latch

10 kΩ or higher

Over latch

Pawl Switch

Tester Connection

Condition

Specified Condition

10 (POL) - 7 (E1)

Open

10 kΩ or higher

Between open and half latch

10 kΩ or higher → Below 1 Ω

Half latch

10 kΩ or higher

Between half latch and full latch

10 kΩ or higher → Below 1 Ω

Full latch

10 kΩ or higher

Over latch

(c) Measure the resistance according to the values in the table below.

Text in Illustration

*a

Component without harness connected

(Power Slide Door Lock Assembly LH)

Standard Resistance:

Neutral Position Switch (NPR)

Tester Connection

Condition

Specified Condition

7 (E1) - 8 (NPR)

Neutral Position (NPR)

10 kΩ or higher

Neutral Position (NPC)

Active lever moved to release operation side

Below 1 Ω

Active lever moved to close operation side

10 kΩ or higher

Neutral Position Switch (NPC)

Tester Connection

Condition

Specified Condition

7 (E1) - 9 (NPC)

Neutral Position (NPR)

10 kΩ or higher

Neutral Position (NPC)

Active lever moved to release operation side

Below 1 Ω

Active lever moved to close operation side

10 kΩ or higher

If the result is not as specified, replace the power slide door lock.

8. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH

(a) Check the operation of the slide door closer motor.

Text in Illustration

*a

Component without harness connected

(Power Slide Door Lock Assembly RH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 1 (ACT+)

Battery negative (-) → 4 (ACT-)

Close rotation

Battery positive (+) → 4 (ACT-)

Battery negative (-) → 1 (ACT+)

Release rotation

If the result is not as specified, replace the power slide door lock.

(b) Measure the resistance according to the values in the table below.

Text in Illustration

*a

Component without harness connected

(Power Slide Door Lock Assembly RH)

Standard Resistance:

Full Latch Switch

Tester Connection

Condition

Specified Condition

6 (FUL) - 7 (E1)

Open

Below 1 Ω

Half latch

Full latch

10 kΩ or higher

Over latch

Half Latch Switch

Tester Connection

Condition

Specified Condition

5 (HAF) - 7 (E1)

Open

Below 1 Ω

Full latch

10 kΩ or higher

Over latch

Pawl Switch

Tester Connection

Condition

Specified Condition

10 (POL) - 7 (E1)

Open

10 kΩ or higher

Between open and half latch

10 kΩ or higher → Below 1 Ω

Half latch

10 kΩ or higher

Between half latch and full latch

10 kΩ or higher → Below 1 Ω

Full latch

10 kΩ or higher

Over latch

(c) Measure the resistance according to the values in the table below.

Text in Illustration

*a

Component without harness connected

(Power Slide Door Lock Assembly RH)

Standard Resistance:

Neutral Position Switch (NPR)

Tester Connection

Condition

Specified Condition

7 (E1) - 8 (NPR)

Neutral Position (NPR)

10 kΩ or higher

Neutral Position (NPC)

Active lever moved to release operation side

Below 1 Ω

Active lever moved to close operation side

10 kΩ or higher

Neutral Position Switch (NPC)

Tester Connection

Condition

Specified Condition

7 (E1) - 9 (NPC)

Neutral Position (NPR)

10 kΩ or higher

Neutral Position (NPC)

Active lever moved to release operation side

Below 1 Ω

Active lever moved to close operation side

10 kΩ or higher

If the result is not as specified, replace the power slide door lock.