Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJAY
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 11/2017]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AB5; Open in Outer Mirror Indicator(Slave); 2016 - 2017 MY Sienna [12/2015 - 11/2017]

DTC

C1AB5

Open in Outer Mirror Indicator(Slave)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No.

DTC Detection Condition

Trouble Area

C1AB5

Both of the following conditions are met:

  • Blind spot monitor main switch (warning canceling switch assembly) is on.
  • The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.
  • Outer rear view mirror LH
  • Outer rear view mirror assembly LH
  • Harness or connector
  • Blind spot monitor sensor LH
  • *1: w/ Seat Position Memory System

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

PROCEDURE

1.

CHECK DTC

(a) Clear the DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: DTC CHECK / CLEAR ).

(b) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

(See page 2016 MY Sienna [12/2015 - 08/2016]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING )
NG

2.

CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)

(a) Disconnect the q3 blind spot monitor sensor LH connector.

(b) Disconnect the H5*1 or H13*2 outer rear view mirror assembly LH connector.

  • *1: w/ Seat Position Memory System
  • *2: w/o Seat Position Memory System

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

w/ Seat Position Memory System

Tester Connection

Condition

Specified Condition

q3-4 (OMIL) - H5-6 (BSL+)

Always

Below 1 Ω

H5-2 (-) - Body ground

Always

Below 1 Ω

w/o Seat Position Memory System

Tester Connection

Condition

Specified Condition

q3-4 (OMIL) - H13-6 (BSL+)

Always

Below 1 Ω

H13-5 (-) - Body ground

Always

Below 1 Ω
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

(a) Disconnect the H5*1 or H13*2 outer rear view mirror assembly LH connector.

  • *1: w/ Seat Position Memory System
  • *2: w/o Seat Position Memory System

(b) Disconnect the IND2 outer rear view mirror LH (outer rear view mirror indicator LH) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

w/ Seat Position Memory System

Tester Connection

Condition

Specified Condition

H5-6 (BSL+) - IND2-2 (+)

Always

Below 1 Ω

H5-2 (-) - IND2-4 (-)

Always

Below 1 Ω

w/o Seat Position Memory System

Tester Connection

Condition

Specified Condition

H13-6 (BSL+) - IND2-2 (+)

Always

Below 1 Ω

H13-5 (-) - IND2-4 (-)

Always

Below 1 Ω
NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

OK

4.

REPLACE OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

(a) Replace the outer rear view mirror LH (outer rear view mirror indicator LH) (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; MIRROR (EXT): OUTER REAR VIEW MIRROR: REMOVAL ).

NEXT

5.

CHECK DTC

(a) Clear the DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: DTC CHECK / CLEAR ).

(b) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END (OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH) WAS DEFECTIVE)
NG

REPLACE BLIND SPOT MONITOR SENSOR LH