Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJAV
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 11/2017]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AB2; Short to GND in Outer Mirror Indicator(Master); 2016 - 2017 MY Sienna [12/2015 - 11/2017]

DTC

C1AB2

Short to GND in Outer Mirror Indicator(Master)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a ground short in the outer rear view mirror indicator RH.

DTC No.

DTC Detection Condition

Trouble Area

C1AB2

Both of the following conditions are met:

  • Blind spot monitor main switch (warning canceling switch assembly) is on.
  • The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time.
  • Outer rear view mirror RH
  • Outer rear view mirror assembly RH
  • Harness or connector
  • Blind spot monitor sensor RH

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

PROCEDURE

1.

CHECK DTC

(a) Clear the DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: DTC CHECK / CLEAR ).

(b) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

(See page 2016 MY Sienna [12/2015 - 08/2016]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2017 MY Sienna [08/2016 - 11/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING )
NG

2.

CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)

(a) Disconnect the q2 blind spot monitor sensor RH connector.

(b) Disconnect the G5*1 or G13*2 outer rear view mirror assembly RH connector.

  • *1: w/ Seat Position Memory System
  • *2: w/o Seat Position Memory System

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

w/ Seat Position Memory System

Tester Connection

Condition

Specified Condition

G5-6 (BSR+) or q2-4 (OMIR) - Body ground

Always

10 kΩ or higher

w/o Seat Position Memory System

Tester Connection

Condition

Specified Condition

G13-6 (BSR+) or q2-4 (OMIR) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

(a) Disconnect the G5*1 or G13*2 outer rear view mirror assembly RH connector.

  • *1: w/ Seat Position Memory System
  • *2: w/o Seat Position Memory System

(b) Disconnect the IND1 outer rear view mirror RH (outer rear view mirror indicator RH) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

w/ Seat Position Memory System

Tester Connection

Condition

Specified Condition

G5-6 (BSR+) - Body ground

Always

10 kΩ or higher

w/o Seat Position Memory System

Tester Connection

Condition

Specified Condition

G13-6 (BSR+) - Body ground

Always

10 kΩ or higher
NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

OK

4.

REPLACE OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

(a) Replace the outer rear view mirror RH (outer rear view mirror indicator RH) (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; MIRROR (EXT): OUTER REAR VIEW MIRROR: REMOVAL ).

NEXT

5.

CHECK DTC

(a) Clear the DTCs (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: DTC CHECK / CLEAR ).

(b) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END (OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH) WAS DEFECTIVE)
NG

REPLACE BLIND SPOT MONITOR SENSOR RH