- Combination meter assembly
- Navigation receiver assembly
- Harness or connector
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000VJ7R |
| Model Year Start: 2016 | Model: Sienna | Prod Date Range: [12/2015 - 11/2017] |
| Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: B1324; Lost Communication with Meter; 2016 - 2017 MY Sienna [12/2015 - 11/2017] | ||
|
DTC |
B1324 |
Lost Communication with Meter |
DESCRIPTION
This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter assembly.
|
DTC No. |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B1324 |
After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the ignition switch is ACC, 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more. |
|
WIRING DIAGRAM
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the D159 navigation receiver assembly connector.
(b) Disconnect the D145 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
D159-3 (CNH1) - D145-18 (MSCH) |
Always |
Below 1 Ω |
|
D159-4 (CNL1) - D145-19 (MSCL) |
Always |
Below 1 Ω |
|
D159-3 (CNH1) - Body ground |
Always |
10 kΩ or higher |
|
D159-4 (CNL1) - Body ground |
Always |
10 kΩ or higher |
|
D159-3 (CNH1) - D159-4 (CNL1) |
Always |
10 kΩ or higher |
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
D159-3 (CNH1) - Body ground |
Always |
Below 1 V |
|
D159-4 (CNL1) - Body ground |
Always |
Below 1 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
INSPECT COMBINATION METER ASSEMBLY |
|
(a) Remove the combination meter assembly (See page
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
18 (MSCH) - 19 (MSCL) |
Always |
108 to 132 Ω |
Text in Illustration
|
*a |
Component without harness connected (Combination Meter Assembly) |
| NG |
|
|
|
3. |
INSPECT NAVIGATION RECEIVER ASSEMBLY |
|
(a) Remove the navigation receiver assembly (See page
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (CNH1) - 4 (CNL1) |
Always |
108 to 132 Ω |
Text in Illustration
|
*a |
Component without harness connected (Navigation Receiver Assembly) |
| NG |
|
|
|
4. |
REPLACE COMBINATION METER ASSEMBLY |
(a) Replace the combination meter assembly with a new or known good one (See page
![2016 - 2020 MY Sienna [12/2015 - ]; METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL](/t3Portal/stylegraphics/info.gif)
).
(b) Clear the DTCs (See page
).
(c) Recheck for DTCs and check that no DTCs are output.
OK:
No DTCs are output.
| NG |
|
|
|
5. |
CHECK METER / GAUGE SYSTEM |
(a) Turn the ignition switch to ON and wait 30 seconds.
(b) Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.
OK:
Audio system returns to normal.
| OK |
|
END (COMBINATION METER ASSEMBLY WAS DEFECTIVE) |
| NG |
|
|
|