Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000000VJ44 |
Model Year Start: 2016 |
Model: Sienna |
Prod Date Range: [12/2015 - 11/2017] |
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Steering Pad Switch Circuit; 2016 - 2017 MY Sienna [12/2015 - 11/2017] |
Steering Pad Switch Circuit
|
DESCRIPTION
This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.
Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself cannot function.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (See page
).
PROCEDURE
1.
|
INSPECT STEERING PAD SWITCH ASSEMBLY
|
(a) Remove the steering pad switch assembly (See page
).
(b) Inspect the steering pad switch assembly (See page
).
OK
|
|
|
2.
|
INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
|
(a) Remove the spiral cable with sensor sub-assembly (See page
).
(b) Inspect the spiral cable with sensor sub-assembly (See page
).
Result
Result
|
Proceed to
|
OK (w/o Steering Heater)
|
A
|
OK (w/ Steering Heater)
|
B
|
NG
|
C
|
A
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)
|
(a) Disconnect the D155 radio and display receiver assembly connector.
(b) Disconnect the D21 spiral cable with sensor sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
D155-21 (SW1) - D21-6 (AU1)
|
Always
|
Below 1 Ω
|
D155-22 (SW2) - D21-5 (AU2)
|
Always
|
Below 1 Ω
|
D155-24 (SW3) - D21-3 (AU3)*1
|
Always
|
Below 1 Ω
|
D155-23 (SWG) - D21-4 (EAU)
|
Always
|
Below 1 Ω
|
D155-21 (SW1) - Body ground
|
Always
|
10 kΩ or higher
|
D155-22 (SW2) - Body ground
|
Always
|
10 kΩ or higher
|
D155-24 (SW3) - Body ground*1
|
Always
|
10 kΩ or higher
|
D155-23 (SWG) - Body ground
|
Always
|
10 kΩ or higher
|
OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
(See page
)
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
4.
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)
|
(a) Disconnect the D155 radio and display receiver assembly connector.
(b) Disconnect the D149 spiral cable with sensor sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
D155-21 (SW1) - D149-6 (AU1)
|
Always
|
Below 1 Ω
|
D155-22 (SE2) - D149-5 (AU2)
|
Always
|
Below 1 Ω
|
D155-23 (SWG) - D149-4 (EAU)
|
Always
|
Below 1 Ω
|
D155-21 (SW1) - Body ground
|
Always
|
10 kΩ or higher
|
D155-22 (SW2) - Body ground
|
Always
|
10 kΩ or higher
|
D155-23 (SWG) - Body ground
|
Always
|
10 kΩ or higher
|
OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
(See page
)
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|