Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VJ0I
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: STEERING COLUMN: STEERING LOCK SYSTEM: DATA LIST / ACTIVE TEST; 2016 - 2020 MY Sienna [12/2015 -        ]

DATA LIST / ACTIVE TEST

1. READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Turn the engine switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch on (IG).

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / (desired system) / Data List.

(f) According to the display on the Techstream, read the Data List.

Smart Key

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Ignition Switch

Engine switch status/ON or OFF

ON: Engine switch on (IG)

OFF: Engine switch off

-

#Codes

Number of diagnostic trouble codes/0 to 255

-

-

Steering Lock Sleep Cond

Steering lock ECU sleep mode possible/Yes or No

Yes: Sleep mode possible

No: Sleep mode not possible

-

Steering Lock Start Cond

Steering lock ECU wake up signal sent/Yes or No

Yes: Wake up signal sent

No: Wake up signal not sent

-

Engine Start Condition

Engine start status/OK or NG

NG: Engine start not possible

OK: Engine start possible

-

Sensor Value

Sensor malfunction record/NG (PAST) or OK

NG (PAST): Sensor malfunction

OK: No malfunction

-

Power Supply Short

Short in ECU record/NG (PAST) or OK

NG (PAST): Short in ECU

OK: No malfunction

-

Power Supply Open

Open in ECU record/NG (PAST) or OK

NG (PAST): Open in ECU

OK: No malfunction

-

Motor Driver Short

Short in driver ECU record/NG (PAST) or OK

NG (PAST): Short in driver ECU

OK: No malfunction

If NG (PAST) is displayed, proceed to troubleshooting for DTC B2782.

Motor Driver Open

Open in driver ECU record/NG (PAST) or OK

NG (PAST): Open in driver ECU

OK: No malfunction

If NG (PAST) is displayed, proceed to troubleshooting for DTC B2782.

Lock/Unlock Receive

Steering lock command reception record/YES or NO

YES: Steering lock/unlock signal received

NO: Steering lock/unlock signal not received

-

Lock Bar Stuck Error

Lock bar stuck malfunction record/NG (PAST) or OK

NG (PAST): Lock bar stuck malfunction

OK: No malfunction

-

Push Start Error

Push button start function malfunction/NG (PAST) or OK

NG (PAST): Malfunction in push button start

OK: No malfunction

-

IG2 Status

IG2 voltage status/ON or OFF

ON: 11 to 14 V

OFF: Below 1 V

-

IG(Lin)

IG signal via LIN communication/ON or OFF

ON: IG signal sent via LIN communication

OFF: IG signal not sent via LIN communication

-

S Code Check

S code certification result/NG or OK

NG: S code certification result abnormal

OK: S code certification result normal

-

L Code Check

L code certification result/NG or OK

NG: L code certification result abnormal

OK: L code certification result normal

-

Unlock Request Receive

Steering lock unlock command reception status/NG or OK

NG: Unlock request not received

OK: Unlock request received

-

Lock Request Receive

Steering lock lock command reception status/NG or OK

NG: Lock request not received

OK: Lock request received

-

S Code Check(Past)

S code certification result/NG (PAST) or OK

NG (PAST): S code certification result abnormal

OK: S code certification result normal

-

L Code Check(Past)

L code certification result/NG (PAST) or OK

NG (PAST): L code certification result abnormal

OK: L code certification result normal

-

Main Body

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

FL Door Courtesy

Front door courtesy switch LH/ON or OFF

ON: Front LH side door closed

OFF: Front LH side door open

-

2. PERFORM ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Power Source Control / Active Test.

(e) According to the display on the Techstream, perform the Active Test.

Power Source Control

Tester Display

Test Part

Control Range

Diagnostic Note

P Supply for Steering Lock

Power management control ECU

Supply or Stop

This test supplies or stops power to the steering lock motor.