Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VIVZ
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 11/2017]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C1432; Steering Angle Sensor Power Source Voltage Malfunction; 2016 - 2017 MY Sienna [12/2015 - 11/2017]

DTC

C1432

Steering Angle Sensor Power Source Voltage Malfunction

DESCRIPTION

Steering angle sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering angle sensor zero point malfunction diagnostic function.

DTC Code

DTC Detection Condition

Trouble Area

C1432

Steering angle sensor power supply malfunction signal is received from steering angle sensor.

  • Steering angle sensor power supply
  • Steering angle sensor (Spiral sensor with cable sub-assembly)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:

  • When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1432, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page 2016 MY Sienna [12/2015 - 08/2016]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: U0073,U0100,U0123,U0124,U0126; Control Module Communication Bus OFF 2017 MY Sienna [08/2016 - 11/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: U0073,U0100,U0123,U0124,U0126; Control Module Communication Bus OFF ).
  • When the speed sensor or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Remove the steering wheel and the column cover lower.

(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

(c) Disconnect the steering angle sensor (spiral sensor with cable sub-assembly) connector.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D22-5 (IG) - Body ground

Ignition switch ON

11 to 14 V

D22-6 (BAT) - Body ground

Always

11 to 14 V

Text in Illustration

*a

Front view of wire harness connector

(to Steering Angle Sensor (Spiral Sensor with Cable Sub-assembly))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK

2.

CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

(a) Turn the ignition switch off.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D22-2 (ESS) - Body ground

Always

Below 1 Ω

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page 2016 MY Sienna [12/2015 - 08/2016]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: PROBLEM SYMPTOMS TABLE 2017 MY Sienna [08/2016 - 11/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: PROBLEM SYMPTOMS TABLE ).

Text in Illustration

*a

Front view of wire harness connector

(to Steering Angle Sensor (Spiral Sensor with Cable Sub-assembly))

OK

REPLACE SPIRAL SENSOR WITH CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)