- An open in the speed sensor signal circuit continues for 0.5 seconds or more.
- With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000VIVR |
| Model Year Start: 2016 | Model: Sienna | Prod Date Range: [12/2015 - 11/2017] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C1405,C1406; Open or Short in Front Speed Sensor RH Circuit; 2016 - 2017 MY Sienna [12/2015 - 11/2017] | ||
|
DTC |
C1405 |
Open or Short in Front Speed Sensor RH Circuit |
|
DTC |
C1406 |
Open or Short in Front Speed Sensor LH Circuit |
DESCRIPTION
The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.
Speed sensor rotors have 48 serrations and their magnetic fields change when the rotors turn. Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.
The hall IC type speed sensor uses the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.
HINT:
Measure the connection status between the sensor connector and the vehicle wire harness.
|
DTC Code |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
C1405 C1406 |
Either of the following is detected: |
|
HINT:
- DTC C1405 is for the front speed sensor RH.
- DTC C1406 is for the front speed sensor LH.
WIRING DIAGRAM
Refer to DTCs C1401 and C1402 (See page
![2016 - 2017 MY Sienna [12/2015 - 11/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C1401,C1402; Front Speed Sensor RH Malfunction+](/t3Portal/stylegraphics/info.gif)
).
CAUTION / NOTICE / HINT
NOTICE:
When replacing the brake actuator assembly, perform zero point calibration and store system information (See page
).
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
(a) Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page
).
ABS/VSC/TRAC
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
FR Speed Open |
FR speed sensor open detection / Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
|
FL Speed Open |
FL speed sensor open detection / Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
OK:
There are no momentary interruptions.
HINT:
Perform the above inspection before removing the sensor and connector.
| NG |
|
|
|
2. |
READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR) |
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Start the engine.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / ABS/VSC/ TRAC / Data List.
(f) Select the Data List on the Techstream (See page
).
ABS/VSC/TRAC
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
FR Wheel Speed |
Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
FL Wheel Speed |
Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
(g) Check that the speed value output from the speed sensor displayed on the Techstream.
HINT:
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page
).
OK:
The speed value output from the speed sensor displayed on the Techstream is the similar speed as indicated on the speedometer.
| NG |
|
|
|
3. |
RECONFIRM DTC |
(a) Turn the ignition switch off.
(b) Clear the DTCs (See page
).
(c) Start the engine.
(d) Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
(e) Check if the same DTC is recorded (See page
).
Result
|
Result |
Proceed to |
|---|---|
|
DTCs (C1405 and C1406) are not output |
A |
|
DTCs (C1405 and/or C1406) are output |
B |
HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page
).
| A |
|
CHECK FOR INTERMITTENT PROBLEMS (See page
|
| B |
|
|
4. |
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
(a) Turn the ignition switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
(c) Disconnect the skid control ECU connector and the front speed sensor connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for RH
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A4-7 (FR+) - A20-2 (FR+) |
Always |
Below 1 Ω |
|
A4-7 (FR+) - Body ground |
Always |
10 kΩ or higher |
|
A4-6 (FR-) - A20-1 (FR-) |
Always |
Below 1 Ω |
|
A4-6 (FR-) - Body ground |
Always |
10 kΩ or higher |
for LH
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A4-19 (FL+) - A6-2 (FL+) |
Always |
Below 1 Ω |
|
A4-19 (FL+) - Body ground |
Always |
10 kΩ or higher |
|
A4-18 (FL-) - A6-1 (FL-) |
Always |
Below 1 Ω |
|
A4-18 (FL-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT SKID CONTROL ECU (SENSOR INPUT) |
|
(a) Reconnect the skid control ECU connector. |
|
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
for RH
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
A20-2 (FR+) - Body ground |
Ignition switch ON |
8 to 14 V |
for LH
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
A6-2 (FL+) - Body ground |
Ignition switch ON |
8 to 14 V |
NOTICE:
Check the speed sensor signal after replacement (See page
).
HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page
).
Text in Illustration
|
*a |
Front view of wire harness connector (to Front Speed Sensor) |
| OK |
|
| NG |
|
|
|