Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VIU8
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: C2121/21-C2124/24,C2181/81-C2184/84; No Signal from Transmitter ID1; 2016 - 2020 MY Sienna [12/2015 -        ]

DTC

C2121/21

No Signal from Transmitter ID1

DTC

C2122/22

No Signal from Transmitter ID2

DTC

C2123/23

No Signal from Transmitter ID3

DTC

C2124/24

No Signal from Transmitter ID4

DTC

C2181/81

Transmitter ID1 not Received (Test Mode DTC)

DTC

C2182/82

Transmitter ID2 not Received (Test Mode DTC)

DTC

C2183/83

Transmitter ID3 not Received (Test Mode DTC)

DTC

C2184/84

Transmitter ID4 not Received (Test Mode DTC)

DESCRIPTION

The tire pressure warning valves and transmitters that are installed in the tire and wheel assemblies measure the air pressure of the tires. The measured values are transmitted to the tire pressure warning antenna and receiver on the body as radio waves and then sent to the tire pressure warning ECU. The ECU compares the measured air pressure values with the air pressure threshold. When the measured air pressure value is less than this threshold, the warning light in the combination meter turns on.

The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning antenna and receiver.

Under the conditions below, the tire pressure warning antenna and receiver is unable to receive the signals from the tire pressure warning valves and transmitters, and a DTC is stored.

  • Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
  • Devices using similar radio frequencies are used in the vehicle.
  • The ID of the tire pressure warning valve and transmitter is mistyped during registration.
  • A tire/wheel/transmitter from a different vehicle is installed.
  • Accessories are installed, such as tire chains or window film, which obstruct the radio signal of the tire pressure warning valve and transmitter.

HINT:

These DTCs are detected when the vehicle is driven and no signals are received for 20 minutes or more.

DTCs from C2121/21 to C2124/24 can only be cleared by using the tester or receiving the signal from the tire pressure warning valve and transmitter. DTCs from C2181/81 to C2184/84 can be cleared when the transmitter in the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs from C2181/81 to C2184/84 are output only in test mode.

DTC No.

DTC Detection Condition

Trouble Area

C2121/21

C2122/22

C2123/23

C2124/24

When all conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode
  • Signal is not received from tire pressure warning valve and transmitter when driving the vehicle at more than 8 km/h (5 mph) for 20 minutes or more
  • Tire pressure warning valve and transmitter
  • Tire pressure warning antenna and receiver
  • Harness or connector
  • Tire pressure warning ECU

C2181/81

C2182/82

C2183/83

C2184/84

Test mode procedure is performed.

  • Tire pressure warning valve and transmitter
  • Tire pressure warning antenna and receiver
  • Harness or connector
  • Tire pressure warning ECU

HINT:

It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using the Techstream and write them down before removal.
  • It is necessary to perform initialization (See page 2016 - 2020 MY Sienna [12/2015 -        ]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: INITIALIZATION ) after registration (See page 2016 - 2020 MY Sienna [12/2015 -        ]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: REGISTRATION ) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or the tire pressure warning valve and transmitter has been replaced.

PROCEDURE

1.

READ OUTPUT DTC (DTC C2174/74)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Tire Pressure Monitor / Trouble Codes.

(f) Read DTCs.

Result

Result

Proceed to

DTC C2174/74 is not output

A

DTC C2174/74 is output

B

NOTICE:

When DTC C2174/74 is output, troubleshoot that DTC first. Then troubleshoot DTCs C2121/21 to C2124/24.

B

GO TO DTC C2174/74

A

2.

CHECK FREQUENCY RECEIVING CONDITION

(a) Check if the vehicle is in conditions such as the ones described below:

(1) Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in areas described above, the tire pressure warning light may blink for a minute and turn on in a particular area.

(2) Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.

HINT:

Radio frequency may be interrupted due to surroundings or devices installed by the user.

NG

CHECK IF ANY DEVICE IS INSTALLED BY USER

OK

3.

IDENTIFY TRANSMITTER CORRESPONDING TO DTC

(a) Set the tire pressure to the appropriate specified values (See page 2016 MY Sienna [12/2015 - 08/2016]; TIRE / WHEEL: TIRE AND WHEEL SYSTEM: INSPECTION 2017 - 2020 MY Sienna [08/2016 -        ]; TIRE / WHEEL: TIRE AND WHEEL SYSTEM: INSPECTION ).

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(g) Check the values by referring to the table below.

Tire Pressure Monitor

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

ID1 Tire Inflation Pressure

ID1 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID2 Tire Inflation Pressure

ID2 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID3 Tire Inflation Pressure

ID3 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID4 Tire Inflation Pressure

ID4 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

HINT:

*: It may take up to 5 or 6 minutes until the values are displayed.

(h) Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

(i) Check the Data List.

NOTICE:

  • It takes up to 5 or 6 minutes to display the updated tire pressure data.
  • When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.
  • Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.

(j) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID4) has changed, repeat this procedure for the other tires. Identify the transmitter that corresponds to the DTC.

Result

Condition

Proceed to

All abnormal

A

One or more transmitters are abnormal

B

All normal

C

B

GO TO STEP 5

C

END

A

4.

CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)

(a) Disconnect the D82 ECU connector.

(b) Disconnect the K16 receiver connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D82-12 (RDA) - K16-1 (RDA)

Always

Below 1 Ω

D82-11 (GND2) - K16-4 (GND)

Always

Below 1 Ω

D82-6 (RF5V) - K16-5 (+5V)

Always

Below 1 Ω

D82-12 (RDA) - Body ground

Always

10 kΩ or higher

D82-11 (GND2) - Body ground

Always

10 kΩ or higher

D82-6 (RF5V) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

CHECK TRANSMITTER ID

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(f) Check the values by referring to the table below.

Tire Pressure Monitor

Tester Display

Measurement Item/Display

Normal Condition

Diagnostic Note

Registered ID1 Code

Registered ID1 code/

min.: 0

max.: FFFFFFFF*

The ID No. registered in the transmitter ID1 is displayed

*: Displayed only when the ID No. is not registered.

Registered ID2 Code

Registered ID2 code/

min.: 0

max.: FFFFFFFF*

The ID No. registered in the transmitter ID2 is displayed

*: Displayed only when the ID No. is not registered.

Registered ID3 Code

Registered ID3 code/

min.: 0

max.: FFFFFFFF*

The ID No. registered in the transmitter ID3 is displayed

*: Displayed only when the ID No. is not registered.

Registered ID4 Code

Registered ID4 code/

min.: 0

max.: FFFFFFFF*

The ID No. registered in the transmitter ID4 is displayed

*: Displayed only when the ID No. is not registered.

(g) Check the transmitter ID on the identified transmitter by removing it from the tire and wheel.

Text in Illustration

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (8-digit number)

-

-

(h) Confirm that the transmitter ID on the transmitter and recorded transmitter ID match.

Result

Result

Proceed to

Match

A

Do not match

B

B

GO TO STEP 7

A

6.

REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

(a) Replace the tire pressure warning valve and transmitter (See page 2016 - 2020 MY Sienna [12/2015 -        ]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING VALVE: REMOVAL ).

NEXT

7.

REGISTRATION OF TRANSMITTER ID

(a) Perform registration (See page 2016 - 2020 MY Sienna [12/2015 -        ]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: REGISTRATION ).

NEXT

8.

PERFORM INITIALIZATION

(a) Perform initialization (See page 2016 - 2020 MY Sienna [12/2015 -        ]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: INITIALIZATION ).

NEXT

9.

READ VALUE USING TECHSTREAM (TIRE INFLATION PRESSURE)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(f) Check the values by referring to the table below.

Tire Pressure Monitor

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

ID1 Tire Inflation Pressure

ID1 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID2 Tire Inflation Pressure

ID2 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID3 Tire Inflation Pressure

ID3 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID4 Tire Inflation Pressure

ID4 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

HINT:

  • *: It may take up to 5 or 6 minutes until the values are displayed.
  • When no "ID Tire Inflation Pressure" has changed, rotate the tire 90 to 270°. Then recheck it.

Result

Result

Proceed to

Tire pressure values are not displayed.

A

All tire pressure readings are equal to specified values.

B

B

END

A

10.

REPLACE TIRE PRESSURE WARNING ANTENNA AND RECEIVER

(a) Replace the tire pressure warning antenna and receiver (See page 2016 - 2020 MY Sienna [12/2015 -        ]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING RECEIVER: REMOVAL ).

NEXT

11.

READ VALUE USING TECHSTREAM (TIRE INFLATION PRESSURE)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(f) Check the values by referring to the table below.

Tire Pressure Monitor

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

ID1 Tire Inflation Pressure

ID1 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID2 Tire Inflation Pressure

ID2 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID3 Tire Inflation Pressure

ID3 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

ID4 Tire Inflation Pressure

ID4 tire inflation pressure /

min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)

Actual tire inflation pressure

If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received.*

HINT:

  • *: It may take up to 5 or 6 minutes until the values are displayed.
  • When no "ID Tire Inflation Pressure" has changed, rotate the tire 90 to 270°. Then recheck it.

Result

Result

Proceed to

All tire pressure readings are equal to specified values.

A

Tire pressure values are not displayed.

B

A

END

B

REPLACE TIRE PRESSURE WARNING ECU