- Open or short in shift solenoid valve SLT circuit
- Shift solenoid valve SLT
- Transmission wire
- TCM
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000VIMR |
| Model Year Start: 2016 | Model: Sienna | Prod Date Range: [12/2015 - 08/2016] |
| Title: U660F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P2716; Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT); 2016 MY Sienna [12/2015 - 08/2016] | ||
|
DTC |
P2716 |
Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) |
DESCRIPTION
Refer to DTC P2714 (See page
![2016 MY Sienna [12/2015 - 08/2016]; U660F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P2714; Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)+](/t3Portal/stylegraphics/info.gif)
).
|
DTC No. |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
P2716 |
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic). |
|
MONITOR DESCRIPTION
When an open or short in the linear solenoid valve (SLT) circuit is detected, the TCM interprets this as a fault. The TCM will turn on the MIL and store the DTC.
MONITOR STRATEGY
|
Related DTCs |
P2716: Shift solenoid valve SLT/Range check |
|
Required sensors/Components |
Shift solenoid valve SLT |
|
Frequency of operation |
Continuous |
|
Duration |
1 second |
|
MIL operation |
Immediate |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
ALL:
|
The monitor will run whenever this DTC is not present |
None |
|
Solenoid current cut status |
Not cut |
|
Ignition switch |
ON |
|
Starter |
OFF |
Condition (A):
One of the following conditions is met: (a) or (b)|
(a) |
|
|
Battery voltage |
12 V or more |
|
(b) |
|
|
All of the following conditions are met |
|
|
Battery voltage |
10 V or more and less than 12 V |
|
Target current |
Less than 0.75 A |
Condition (B):
|
Battery voltage |
8 V or more |
|
Target current |
0.25 A or more |
Condition (C):
|
Battery voltage |
11 V or more |
|
Target current |
1 A or more |
Condition (D):
|
Battery voltage |
11 V or more |
|
Target current |
0.1 A or more |
|
l Target voltage - Last target voltage l |
Less than 0.0000191 V |
TYPICAL MALFUNCTION THRESHOLDS
Condition (A):
|
Output duty cycle |
100% or more |
Condition (B):
|
Output duty cycle |
0% or less |
Condition (C):
|
Solenoid voltage monitor |
No signal |
Condition (D):
|
l Target voltage - Average of monitor voltage l |
0.035 V or more |
COMPONENT OPERATING RANGE
|
Output duty cycle |
Less than 100% |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Perform the universal trip to clear permanent DTCs (See page
).
PROCEDURE
|
1. |
INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT) |
|
(a) Remove the TCM from the transaxle. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
12 (SLT+) - 7 (SLT-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
12 (SLT+) - Body ground |
Always |
10 kΩ or higher |
|
7 (SLT-) - Body ground |
Always |
10 kΩ or higher |
|
12 (SLT+) - All other terminals except 7 (SLT-) |
Always |
10 kΩ or higher |
|
7 (SLT-) - All other terminals except 12 (SLT+) |
Always |
10 kΩ or higher |
Text in Illustration
|
*a |
Component without harness connected: (Transmission Wire) |
| OK |
|
|
|
2. |
INSPECT SHIFT SOLENOID VALVE SLT |
|
(a) Remove shift solenoid valve SLT. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
1 - 2 |
20°C (68°F) |
5.0 to 5.6 Ω |
Text in Illustration
|
*a |
Component without harness connected (Shift Solenoid Valve SLT) |
(c) Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
OK:
Valve moves and makes an operating sound.
| OK |
|
| NG |
|
|
|