Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VILO
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2016]
Title: U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P2810; Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4); 2016 MY Sienna [12/2015 - 08/2016]

DTC

P2810

Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4)

DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (See page 2016 MY Sienna [12/2015 - 08/2016]; U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: FAIL-SAFE CHART ).

DTC No.

DTC Detection Condition

Trouble Area

P2810

An open or short circuit (output signal duty is 0% or 100%) is detected by the TCM in the shift solenoid valve SL4 circuit while driving and shifting gears (SL4 output signal duty is more than 3% and less than 100% under normal conditions) (1-trip detection logic).

  • Open or short in shift solenoid valve SL4 circuit
  • Shift solenoid valve SL4
  • Transmission wire
  • TCM

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. The TCM also performs the fail-safe function and turns the other normal shift solenoid valves on or off (In case of an open or short circuit, the TCM stops sending current to the circuit.)

(See page 2016 MY Sienna [12/2015 - 08/2016]; U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: FAIL-SAFE CHART ).

MONITOR STRATEGY

Related DTCs

P0798: Shift solenoid valve SL3/Range check

Required sensors/Components

Shift solenoid valve SL4

Frequency of operation

Continuous

Duration

1 second

MIL operation

Immediate

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

All:

The monitor will run whenever this DTC is not present

None

Ignition switch

ON

Starter

OFF

Condition (A):

One of the following conditions is met: (a) or (b)

a. Battery voltage

12 V or more

b. All of the following conditions are met

 

Battery voltage

10 V or more and less than 12 V

Target current

Less than 0.75 A

Condition (B):

Battery voltage

8 V or more

Target current

0.25 A or more

TYPICAL MALFUNCTION THRESHOLDS

Condition (A):

Output duty cycle

100% or more

Condition (B):

Output duty cycle

0% or less

COMPONENT OPERATING RANGE

Output duty cycle

More than 3% and less than 100%

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR ).

PROCEDURE

1.

INSPECT TRANSMISSION WIRE (SL4)

(a) Remove the TCM from the transaxle.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

22 (SL4+) - 21 (SL4-)

20°C (68°F)

5.0 to 5.6 Ω

22 (SL4+) - Body ground

Always

10 kΩ or higher

21 (SL4-) - Body ground

Always

10 kΩ or higher

22 (SL4+) - All other terminals except 21 (SL4-)

Always

10 kΩ or higher

21 (SL4-) - All other terminals except 22 (SL4+)

Always

10 kΩ or higher

Text in Illustration

*a

Component without harness connected:

(Shift Solenoid Valve SL4)

OK

REPLACE TCM

NG

2.

INSPECT SHIFT SOLENOID VALVE SL4

(a) Remove shift solenoid valve SL4.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20°C (68°F)

5.0 to 5.6 Ω

Text in Illustration

*a

Component without harness connected:

(Shift Solenoid Valve SL4)

(c) Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

OK

REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE SL4