Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VILA
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2016]
Title: U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: HYDRAULIC TEST; 2016 MY Sienna [12/2015 - 08/2016]

HYDRAULIC TEST

1. PERFORM HYDRAULIC TEST

(a) Measure the line pressure.

CAUTION:

The line pressure test should always be carried out with at least 2 people. One person should observe the condition of wheels and wheel chocks while the other is performing the test.

NOTICE:

  • Perform a test at the normal operating Automatic Transmission Fluid (ATF) temperature: 50 to 80°C (122 to 176°F)
  • Be careful to prevent the SST hose from interfering with the exhaust pipe.
  • This check must be conducted after checking and confirming that the engine is normal.
  • Perform the test with the A/C off.
  • Do not perform the stall test for longer than 5 seconds.
  • When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.

(1) Warm up the Automatic Transmission Fluid (ATF).

(2) Lift the vehicle up.

(3) Remove the engine under cover.

(4) Remove the test plug on the transaxle case front left side and install SST.

SST: 09992-00095

09992-00231

09992-00271

(5) Lower the vehicle.

(6) Fully apply the parking brake and chock the 4 wheels.

(7) Connect the Techstream to the DLC3.

(8) Start the engine.

(9) Enter the following menus: Powertrain / ECT / Active Test / Control the Shift Position.

(10) Move the shift lever to D, and then use the Techstream to hold 3rd gear using Active Test. Measure the line pressure while the engine is idling.

Specified Line Pressure:

Condition

D Position kPa (kgf/cm2, psi)

Idling

360 to 430 kPa

(3.7 to 4.4 kgf/cm2, 52 to 62 psi)

(11) Turn the ignition switch off.

(12) Disconnect the connector of the TCM.

HINT:

Disconnect the connector only when performing the D position stall test.

(13) Start the engine.

(14) Firmly depress the brake pedal, move the shift lever to D, depress the accelerator pedal all the way down, and check the line pressure while the stall test is performed.

Specified Line Pressure:

Condition

D Position kPa (kgf/cm2, psi)

Stall test

1160 to 1350 kPa

(11.8 to 13.8 kgf/cm2, 168 to 196 psi)

(15) Turn the ignition switch off.

(16) Connect the TCM connector, depress the brake pedal firmly, move the shift lever to R, and check the line pressure while the engine is idling and during the stall test.

Specified Line Pressure:

Condition

R Position kPa (kgf/cm2, psi)

Idling

800 to 950 kPa

(8.2 to 9.7 kgf/cm2, 116 to 138 psi)

Stall test

1900 to 2200 kPa

(19.4 to 22.4 kgf/cm2, 276 to 319 psi)

(17) Remove SST, install the test plug.

(18) Clear the DTCs.

Evaluation

Test Result

Possible Cause

Measured values are higher than the specified value in all positions

  • Shift solenoid valve (SLT) defective
  • Regulator valve defective

Measured values are lower than the specified value in all positions

  • Shift solenoid valve (SLT) defective
  • Regulator valve defective
  • Oil pump defective

Pressure is low in D only

  • D position circuit fluid leak
  • Clutch No. 1 (C1) defective

Pressure is low in R only

  • R position circuit fluid leak
  • Brake No. 2 (B2) defective
  • Brake No. 3 (B3) defective