Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VIKW
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2016]
Title: U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P2757; Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU); 2016 MY Sienna [12/2015 - 08/2016]

DTC

P2757

Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)

DESCRIPTION

The TCM uses the signals from the throttle position sensor, air-flow meter, input speed sensor (NT), output speed sensor (NC) and crankshaft position sensor (NE) to monitor the engagement condition of the lock-up clutch.

The TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect shift solenoid valve SLU, valve body and torque converter clutch mechanical problems.

DTC No.

DTC Detection Condition

Trouble Area

P2757

When both of the following are detected (2 trip detection logic):

  • Lock-up does not occur when requested.
  • No. 3 ATF pressure switch is OFF.

When both of the following are detected (2 trip detection logic):

  • No. 3 ATF pressure switch is ON when lock-up does not occur.
  • Lock-up occurs when shift solenoid valve SLU is requested to turn on in the lock-up range.
  • Shift solenoid valve SLU remains open or closed
  • Valve body is blocked
  • Torque converter assembly
  • Automatic transaxle (clutch, brake or gear, etc.)
  • Line pressure is too low

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the TCM based on the speed sensor (NT), speed sensor (NC), engine speed (NE), engine load, engine temperature, vehicle speed, automatic transmission fluid (ATF) temperature, and gear selection. The TCM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input speed (NT). The TCM calculates the actual transmission gear by comparing input speed (NT) to output speed (NC). When conditions are appropriate, the TCM requests "lock-up" by applying control voltage to shift solenoid SLU. When SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter assembly.

If the TCM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the TCM interprets this as a fault in shift solenoid valve SLU or lock-up system performance.

The TCM will turn on the MIL and store the DTC.

Example:

When any of the following is met, the system judges it as a malfunction.

  • There is a difference in rotation (speed) between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up.

    (Engine speed is at least 70 rpm greater than input turbine speed.)

  • There is no difference in rotation (speed) between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up off.

    (The difference between engine speed and input turbine speed is less than 35 rpm.)

MONITOR STRATEGY

Related DTCs

P2757:

Shift solenoid valve SLU OFF malfunction

Shift solenoid valve SLU ON malfunction

Required sensors/Components

Shift solenoid valve SLU

Frequency of operation

Continuous

Duration

OFF malfunction (a): 3.5 seconds

OFF malfunction (b): 0.05 seconds

ON malfunction (a): 1.8 seconds

ON malfunction (b): 0.6 seconds

MIL operation

2 driving cycles

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The following items are common to all conditions below.

The monitor will run whenever this DTC is not present.

(Not circuit malfunction)

P0712, P0713 (ATF temperature sensor circuit (TFT sensor))

P0115, P0117, P0118 (ECT sensor circuit)

P0715, P0717 (Input speed sensor (NT) circuit)

P0791, P0793 (Output speed sensor (NC) circuit)

P0748 (Shift solenoid valve SL1 circuit)

P0778 (Shift solenoid valve SL2 circuit)

P0798 (Shift solenoid valve SL3 circuit)

P2810 (Shift solenoid valve SL4 circuit)

P2759 (Shift solenoid valve SLU circuit)

P2769, P2770 (Shift solenoid valve SL circuit)

P0327, P0328, P0332, P0333 (KCS sensor circuit)

P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system)

U0100 (CAN communication system)

Engine coolant temperature

40°C (104°F) or more

Spark advance from Max. retard timing by KCS control

0°CA or more

Transmission range

D

TFT (Transmission fluid temperature)

-10°C (14°F) or more

TFT (Transmission fluid temperature) sensor circuit

No circuit malfunction

ECT (Engine coolant temperature) sensor circuit

No circuit malfunction

Input speed sensor (NT) circuit

No circuit malfunction

Output speed sensor (NC) circuit

No circuit malfunction

Shift solenoid valve SL1 circuit

No circuit malfunction

Shift solenoid valve SL2 circuit

No circuit malfunction

Shift solenoid valve SL3 circuit

No circuit malfunction

Shift solenoid valve SL4 circuit

No circuit malfunction

Shift solenoid valve SLU circuit

No circuit malfunction

Shift solenoid valve SL circuit

No circuit malfunction

KCS (Knock control sensor circuit)

No circuit malfunction

(ETCS) Electronic throttle control system

Not system down

CAN communication system

Not system down

Engine

Starting

TCM selected gear

Not 1st

Vehicle speed

25 km/h (15.5 mph) or more

Input speed (NT) / Output speed (NO) with 1st

3.304 to 7.724

Input speed (NT) / Output speed (NO) with 2nd

1.901 to 2.340

Input speed (NT) / Output speed (NO) with 3rd

1.399 to 1.649

Input speed (NT) / Output speed (NO) with 4th

0.998 to 1.138

Input speed (NT) / Output speed (NO) with 5th

0.705 to 0.836

Input speed (NT) / Output speed (NO) with 6th

0.568 to 0.695

OFF malfunction:

TCM lock-up command

ON

(SLU pressure: 513 kPa (5.2 kgf/ cm2, 74 psi) or more

Duration time from lock-up on command

3 seconds or more

Shift solenoid valve SLU

Not ON malfunction

ON malfunction:

TCM lock-up command

OFF

(SLU pressure: less than 4 kPa (0.04 kgf/ cm2, 0.6 psi)

Duration time from lock-up on command

0.064 seconds or more

Throttle valve opening angle

7% or more

Vehicle speed

Less than 60 km/h (37.3 mph)

Shift solenoid valve SLU

Not malfunction

(P2757)

Shift solenoid valve SL

Not OFF malfunction

(P0741)

No. 3 ATF pressure switch

Not ON malfunction

(P0990)

TYPICAL MALFUNCTION THRESHOLDS

OFF malfunction:

Following conditions are met

(a) and (b)

(a) l Engine speed (NE) - Input speed (NT) l

70 rpm or more

(b) No. 3 ATF pressure switch

OFF

ON malfunction:

Following conditions are met

(a) and (b)

(a) l Engine speed (NE) - Input speed (NT) l

Less than 35 rpm

(b) No. 3 ATF pressure switch

ON

COMPONENT OPERATING RANGE

Input speed sensor (NT)

Input speed is equal to engine speed when lock-up is ON.

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR ).

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

1. ACTIVE TEST

(a) Warm up the engine.

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / ECT / Active Test.

(g) According to the display on the Techstream, perform the Active Test.

ECT

Tester Display

Test Part

Control Range

Diagnostic Note

Activate the Lock Up

Control the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition.

ON/OFF

Can be used to check SLU and SL solenoid operation.

[Vehicle Condition]

  • Vehicle speed: 60 km/h (37 mph) or more

HINT:

  • This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.

(h) Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

HINT:

  • When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
  • Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)

PROCEDURE

1.

CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / ECT / Trouble Codes.

(e) Read the DTCs using the Techstream.

Result

Result

Proceed to

Only P2757 is output

A

P2757 and other DTCs are output

B

HINT:

If any other codes besides P2757 are output, perform troubleshooting for those DTCs first.

B

GO TO DTC CHART

A

2.

INSPECT SHIFT SOLENOID VALVE SLU

(a) Remove shift solenoid valve SLU.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20°C (68°F)

5.0 to 5.6 Ω

Text in Illustration

*a

Component without harness connected:

(Shift Solenoid Valve SLU)

(c) Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

NG

REPLACE SHIFT SOLENOID VALVE SLU

OK

3.

INSPECT TRANSMISSION VALVE BODY ASSEMBLY

(a) Check the transmission valve body assembly (See page 2016 MY Sienna [12/2015 - 08/2016]; U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): VALVE BODY ASSEMBLY(When Not Using the Engine Support Bridge): REMOVAL ).

OK:

There are no foreign objects on each valve and they operate smoothly.

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

OK

4.

INSPECT TORQUE CONVERTER ASSEMBLY

(a) Check the torque converter assembly (See page 2016 MY Sienna [12/2015 - 08/2016]; U660E (AUTOMATIC TRANSMISSION / TRANSAXLE): TORQUE CONVERTER AND DRIVE PLATE: INSPECTION ).

OK:

The torque converter assembly operates normally.

OK

REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

REPLACE TORQUE CONVERTER ASSEMBLY