| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000VIHG |
| Model Year Start: 2016 | Model: Sienna | Prod Date Range: [12/2015 - 08/2016] |
| Title: CRUISE CONTROL: CRUISE CONTROL SYSTEM: DATA LIST / ACTIVE TEST; 2016 MY Sienna [12/2015 - 08/2016] | ||
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Cruise Control / Data List.
(e) Read the Data List according to the display on the Techstream.
Cruise Control
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
CCS Vehicle Spd |
Vehicle speed/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) |
Actual vehicle speed |
- |
|
CCS Mem Vehicle Spd |
Cruise control memorized speed/min.: 0 km/h (0 mph), max.: 200 km/h (125 mph) |
Actual stored vehicle speed |
- |
|
Throttle Opening Angle |
Throttle opening angle/min.: 0 degrees, max.: 125 degrees |
Actual demanded throttle angle |
- |
|
Cruise Control |
Cruise control system active condition/ON or OFF |
ON: Cruise control activated OFF: Cruise control deactivated |
- |
|
Main SW M-CPU |
Main switch signal (Main CPU)/ON or OFF |
ON: Main switch depressed OFF: Main switch released |
- |
|
CCS Ready M-CPU |
Cruise control system standby condition (Main CPU)/ON or OFF |
Each time main switch is pushed, ON/OFF changes |
- |
|
CCS Indicator M-CPU |
Cruise indicator signal (Main CPU)/ON or OFF |
ON: Cruise main indicator light on OFF: Cruise main indicator light off |
- |
|
Cancel Switch |
CANCEL switch signal/ON or OFF |
ON: While switch is being operated OFF: Switch not operated |
- |
|
SET/COAST Switch |
SET/COAST switch signal/ON or OFF |
ON: While switch is being operated OFF: Switch not operated |
- |
|
RES/ACC Switch |
RES/ACC switch signal/ON or OFF |
ON: While switch is being operated OFF: Switch not operated |
- |
|
Stp Light SW M-CPU |
Stop light switch signal (Main CPU)/ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
|
Cruise Operation Status |
PNP switch signal (D position)/ON or OFF |
ON: Shift lever in D OFF: Shift lever not in D |
- |
|
Brake Cancel Switch |
Brake Cancel signal/ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
HINT:
- If any DTCs are output, the value for a measurement item may be incorrect.
- If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using the Data List.
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) Perform Active Test according to the display on the Techstream.
HINT:
The ignition switch must be turned to ON to proceed with Active Test using the Techstream.
Combination Meter
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Indicat. Lamp Cruise*1 |
Cruise main indicator light (illuminated is green) |
OFF or ON |
- |
|
Indicat. SET*1 |
Cruise control SET indicator light |
OFF or ON |
- |
|
Meter Display 1 |
Multi-information display |
OFF or All |
- |
- *1: for Multi-information Display (Monochrome Type)
|
|