Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VIC7
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2016]
Title: 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P060B; Internal Control Module A/D Processing Performance; 2016 MY Sienna [12/2015 - 08/2016]

DTC

P060B

Internal Control Module A/D Processing Performance

MONITOR DESCRIPTION

This DTC is stored when a communication error occurs in the ECM.

DTC No.

DTC Detection Condition

Trouble Area

P060B

An ECM main CPU communication error (1 trip detection logic).
  • ECM
  • Knock sensor

MONITOR STRATEGY

Related DTCs

P060B: Internal control module A/D processing performance

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

2 times: Case 2

10 times: Case 1

30 times: Case 3 and 4

MIL Operation

Immediately

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Case 1 and 4

Monitor runs whenever the following DTCs are not stored

None

Both of the following conditions are met

-

Battery voltage

8 V or higher

Starter

Off

Case 2 and 3

Monitor runs whenever the following DTCs are not stored

None

TYPICAL MALFUNCTION THRESHOLDS

Case 1

Internal module serial communication

Fail

Case 2

AD converter

Fail

Case 3

Knock sensor circuit

Fail

Case 4

Knock sensor serial communication

Fail

CONFIRMATION DRIVING PATTERN

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page 2016 MY Sienna [12/2015 - 08/2016]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION ).

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR ).
  4. Turn the Techstream off.
  5. Turn the ignition switch off.
  6. Disconnect the Techstream.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the Techstream to the DLC3.
  10. Turn the ignition switch to ON and turn the Techstream on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine / Trouble Codes.
  13. Read pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  14. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  15. Input the DTC: P060B.
  16. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR ).

    HINT:

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTC is output, the system is normal.

CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page 2016 MY Sienna [12/2015 - 08/2016]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION ).

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

READ OUTPUT DTC (DTC P060B)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR ).

(e) Turn the Techstream off.

(f) Turn the ignition switch off.

(g) Disconnect the Techstream.

(h) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

(i) Connect the cable to the negative (-) battery terminal.

(j) Connect the Techstream to the DLC3.

(k) Turn the ignition switch to ON.

(l) Turn the Techstream on.

(m) Wait for 16 seconds or more.

(n) Enter the following menus: Powertrain / Engine / Trouble Codes.

(o) Read the DTCs.

Result

Result

Proceed to

DTC is not output

A

DTC P060B is output

B

DTC P060B and P0327, P0328, P0332 or P0333 are output

C
A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM

C

GO TO DTC (P0327, P0328, P0332 AND P0333)