Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VIAR
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 08/2016]
Title: 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0607; Control Module Performance; 2016 MY Sienna [12/2015 - 08/2016]

DTC

P0607

Control Module Performance

MONITOR DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC No.

DTC Detection Condition

Trouble Area

P0607
  • ECM CPUs malfunction
  • Heated oxygen sensor transistor (built into ECM) malfunction
  • ECM
  • Heated oxygen sensor
  • Exhaust gas leak

MONITOR STRATEGY

Related DTCs

P0607: Control module performance

Required sensors/Components (Main)

ECM

Required sensors/Components (Related)

Heated oxygen sensor

Frequency of operation

Continuous

Duration

60 seconds

MIL operation

Immediately

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs are not present

None

Engine

Running

Estimated heated oxygen sensor temperature

450 to 800°C (842 to 1472°F)

TYPICAL MALFUNCTION THRESHOLDS

Heated oxygen sensor transistors

Fail

CONFIRMATION DRIVING PATTERN

  1. Stop the engine for 30 minutes or more [A].
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch to ON and turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR ) [B].
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on [C].
  7. Start the engine, and wait 2 minutes [D].
  8. Warm up the engine until the engine coolant temperature is 75°C (167°F) or more [E].
  9. Idle the engine for 1 minute [F].
  10. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [G].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  11. Drive the vehicle at 56 to 80 km/h (35 to 50 mph) for 5 minutes or more [H].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Enter the following menus: Powertrain / Engine / Trouble Codes [I].
  13. Read pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  14. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  15. Input the DTC: P0607, P0136, P0137, P0138, P0156, P0157 or P0158.
  16. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:

    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the result shows INCOMPLETE or N/A, perform steps [E] through [I] again.
  17. If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR ).

    HINT:

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTC is output, the system is normal.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK ANY OTHER DTCS OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Trouble Codes.

(e) Read DTCs.

Result

Result

Proceed to

DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output

A

DTC P0607 is output

B
B

GO TO STEP 3

A

2.

INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)

(a) Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.

HINT:

  • If P0136 or P0156 is output, troubleshoot for that DTC first (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0136-P0139,P013A,P013C,P0156-P0159; Oxygen Sensor Circuit (Bank 1 Sensor 2)+ ). Then proceed to "Inspect ECM".
  • If P0137 or P0157 is output, troubleshoot for that DTC first (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0136-P0139,P013A,P013C,P0156-P0159; Oxygen Sensor Circuit (Bank 1 Sensor 2)+ ). Then proceed to "Inspect ECM".
  • If P0138 or P0158 is output, troubleshoot for that DTC first (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0136-P0139,P013A,P013C,P0156-P0159; Oxygen Sensor Circuit (Bank 1 Sensor 2)+ ). Then proceed to "Inspect ECM".
  • If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).
NEXT

GO TO STEP 6

3.

CHECK FOR EXHAUST GAS LEAK

(a) Allow the engine to idle and rev the engine.

(b) Check for exhaust gas leaks around the heated oxygen sensor.

If any exhaust gas leaks are present, repair it and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".

HINT:

  • If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.
  • If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.
  • Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION ).
NEXT

4.

PERFORM CONFIRMATION DRIVING PATTERN

(a) Clear DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR ).

(b) Connect the Techstream to the DLC3.

(c) Start the engine and warm up the engine until the engine coolant temperature becomes 75°C (167°F) or more.

(d) Perform the driving pattern.

(1) Accelerate the vehicle until 80 km/h (50 mph) and stop the vehicle.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

(2) Drive the vehicle between 60 to 80 km/h (37 to 50 mph) for 5 minutes.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

(e) Enter the following menus: Powertrain / Engine / Trouble Codes.

(f) Read the DTCs.

Result

Result

Proceed to

DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output

A

DTC P0607 is output

B

DTC is not output

C
B

REPLACE ECM

C

GO TO STEP 6

A

5.

INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)

(a) Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.

HINT:

  • If P0136 or P0156 is output, troubleshoot for that DTC first (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0136-P0139,P013A,P013C,P0156-P0159; Oxygen Sensor Circuit (Bank 1 Sensor 2)+ ). Then proceed to "Inspect ECM".
  • If P0137 or P0157 is output, troubleshoot for that DTC first (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0136-P0139,P013A,P013C,P0156-P0159; Oxygen Sensor Circuit (Bank 1 Sensor 2)+ ). Then proceed to "Inspect ECM".
  • If P0138 or P0158 is output, troubleshoot for that DTC first (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0136-P0139,P013A,P013C,P0156-P0159; Oxygen Sensor Circuit (Bank 1 Sensor 2)+ ). Then proceed to "Inspect ECM".
  • If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).
NEXT

6.

INSPECT ECM

(a) Clear DTCs (See page 2016 MY Sienna [12/2015 - 08/2016]; 2GR-FE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR ).

(b) Stop the engine and wait for 30 minutes.

(c) Connect the Techstream to the DLC3.

(d) Start the engine and allow it to idle for 2 minutes.

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Engine / Trouble Codes.

(g) Read the DTCs.

Result

Result

Proceed to

DTC is not output

A

DTC P0607 is output

B
A

END
B

REPLACE ECM