- Open or short in stop light switch signal circuit
- Stop light switch assembly
- ECM
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000VIAO |
| Model Year Start: 2016 | Model: Sienna | Prod Date Range: [12/2015 - 08/2016] |
| Title: 2GR-FE (ENGINE CONTROL): SFI SYSTEM: P0504; Brake Switch "A" / "B" Correlation; 2016 MY Sienna [12/2015 - 08/2016] | ||
|
DTC |
P0504 |
Brake Switch "A" / "B" Correlation |
DESCRIPTION
The stop light switch assembly is a duplex system that transmits 2 signals: STP and ST-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.
HINT:
The normal signal conditions are as shown in the table below.
|
Signal (ECM Terminal) |
Brake Pedal Released |
In Transition |
Brake Pedal Depressed |
|---|---|---|---|
|
STP |
OFF |
ON |
ON |
|
ST1- |
ON |
ON |
OFF |
- [OFF] denotes ground potential.
- [ON] denotes battery potential (+B).
- On the Techstream, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.
|
DTC No. |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
P0504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b) Brake pedal is released (c) STP signal is off when ST- signal is off |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
-
Stop light switch conditions can be checked using the Techstream.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch and ST1.
-
Check the Data List indication when the brake pedal is depressed and released.
Brake Pedal Operation
Stop Light Switch
ST1
Depressed
ON
ON
Released
OFF
OFF
PROCEDURE
|
1. |
CHECK SPECIFICATIONS |
Check the vehicle specifications.
Result
|
Result |
Proceed to |
|---|---|
|
for Bulb Type Stop Light |
A |
|
for LED Type Stop Light |
B |
| B |
|
|
|
2. |
CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
|
(a) Disconnect the stop light switch assembly connector. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
A58-2 - Body ground |
Always |
11 to 14 V |
|
A58-4 - Body ground |
Ignition switch ON |
11 to 14 V |
Text in Illustration
|
*a |
Front view of wire harness connector (to Stop Light Switch Assembly) |
Result
|
Result |
Proceed to |
|---|---|
|
NG |
A |
|
OK |
B |
| A |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY) |
| B |
|
|
3. |
CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
|
(a) Disconnect the stop light switch assembly connector. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
A59-2 (B) - Body ground |
Always |
11 to 14 V |
|
A59-5 (B) - Body ground |
Ignition switch ON |
11 to 14 V |
Text in Illustration
|
*a |
Front view of wire harness connector (to Stop Light Switch Assembly) |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY) |
|
|
4. |
INSPECT STOP LIGHT SWITCH ASSEMBLY |
(a) Inspect the stop light switch assembly (for Bulb Type Stop Light) (See page
![2016 - 2020 MY Sienna [12/2015 - ]; LIGHTING (EXT): STOP LIGHT SWITCH: INSPECTION+](/t3Portal/stylegraphics/info.gif)
).
(b) Inspect the stop light switch assembly (for LED Type Stop Light) (See page
).
| NG |
|
|
|
5. |
CHECK ECM (STP AND ST1 - VOLTAGE) |
(a) Disconnect the ECM connector.
Text in Illustration
|
*a |
Brake Pedal Depressed |
*b |
Brake Pedal Released |
|
*c |
Front view of wire harness connector (to ECM) |
- |
- |
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Brake Pedal Operation |
Specified Condition |
|---|---|---|
|
A39-35 (ST-) - Body ground |
Released |
7.5 to 14 V |
|
Depressed |
0 to 1.5 V |
|
|
A39-36 (STP) - Body ground |
Released |
0 to 1.5 V |
|
Depressed |
7.5 to 14 V |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM) |
|
|