• Perform the Diagnostic System Check prior to using this diagnostic procedure:Diagnostic System Check - Vehicle
• Review the description of Strategy Based Diagnosis:Strategy Based Diagnosis
• An overview of each diagnostic category can be found here:Diagnostic Procedure Instructions

Symptom Byte Information:Symptom Byte List

For an overview of the component/system, refer to:Surround Vision Camera Description and Operation

Ignition » On / Vehicle » In Service Mode

Component Internal Malfunction

An internal evaluation logic has detected a malfunction of the circuit.

Incorrect MountingDetected

The Video Processing Control Module has detected a Right Sideview Camera internal malfunction

The Video Processing Control Module has detected a camera video signal circuit malfunction.

The Video Processing Control Module has detected incorrect Right Sideview Camera mounting.

The Video Processing Control Module has determined Right Sideview Camera calibration not complete.

The Video Processing Control Module has determined the Right Sideview Camera temperature is outside normal operating range.

Service Surround Vision Camera message=On

The conditions for setting the DTC no longer exist.

The following conditions could cause component performance issues:B225R Sideview Camera - Right

• Ambient Light Intensity—High/Low
• Camera Blocked—Debris/Ice/Mud/Snow
• Temperature—High/Low

An open in the shield of the video signal circuit can cause a distorted screen.

Image Display Camera Schematics

Master Electrical Component List

• Circuit Testing
• Connector Repairs
• Testing for Intermittent Conditions and Poor Connections
• Wiring Repairs

Control Module References

• EL-52552/EL-52552-50 COAX FAKRA CABLE ADAPTER KIT

Equivalent regional tools:Special Tools

1. Verify no other Video Processor Control Module DTCs are present
• If any other Video Processor Control Module DTCs are set

  Refer to:Diagnostic Trouble Code (DTC) List - Vehicle

• If no other Video Processor Control Module DTCs are set
2. Perform the following visual inspections:
• Misalignment of the components:B225R Sideview Camera - Right
• Visible Damage
• Dirty
• If a condition exists » Repair or replace as necessary
• If none of the conditions exists
3. Refer to: Circuit/System Testing

1. Ignition » On / Vehicle » In Service Mode
2. Replace the component:B225R Sideview Camera - Right
3. Verify DTC B395C is not set
• If DTC B395C is not set

  All OK.

• If DTC B395C is set
4. Replace the component:K157 Video Processing Control Module

1. Ignition/Vehicle & All vehicle systems » Off
2. Disconnect the electrical connector:X4@K157 Video Processing Control Module
3. Wait for greater than 5 s.
4. Connect appropriate EL-52552/EL-52552-50 pinout tool to K157 Video Processing Control Module
5. Ignition » On / Vehicle » In Service Mode
6. Test for 7 to 11 V between the test points:Signal circuit terminal 2-TN (or BG2)@K157 Video Processing Control Module&Ground(component side)
• If not between 7 and 11 V

  Replace the component:K157 Video Processing Control Module

• If between 7 and 11 V
7. Ignition/Vehicle & All vehicle systems » Off

Note: Before testing the coax cable, check the cable's exterior for being pinched, cut, damaged, or having loose connections at the components, all of which can cause reception issues.

8. Disconnect the electrical connector:B225R Sideview Camera - Right
9. Locate the appropriate pinout adapter and load test loop adapter from EL-52552/EL-52552-50 COAX FAKRA Cable Adaptor Kit.
10. Connect the 2 adapters together, measure and record the resistance between the terminals at the pinout adapter.
11. Disconnect the 2 adapters and connect each one to the appropriate end of the coax cable.
12. At the pinout adapter test terminals, measure the total resistance of the coax cable loop including the connected load test adapter.
• If not within 5 Ω of the reading from step 10.

  Replace the coax cable

• If within 5 Ω of the reading from step 10.
13. Replace the component:B225R Sideview Camera - Right
14. Apply the parking brake.
15. Engine RunningTransmission in Reverse
16. Verify DTC B395C is not set
• If the DTC is set

  Replace the component:K157 Video Processing Control Module

• If the DTC is not set
17. All OK.

1. Ignition » On / Vehicle » In Service Mode
2. Operate the vehicle under the following conditions:
• During the day
• On a straight road
• Distance Traveled=Greater than 0.5 km (0.3 mi)
3. Ignition/Vehicle & All vehicle systems » Off
4. Wait for greater than 60 s.
5. Ignition » On / Vehicle » In Service Mode
6. Verify DTC B395C is not set
• If DTC B395C is not set

  All OK.

• If DTC B395C is set
7. Test or replace the component:B225R Sideview Camera - Right
8. Verify DTC B395C is not set
• If DTC B395C is not set

  All OK.

• If DTC B395C is set
9. Test or replace the component:K157 Video Processing Control Module

Note: DTC B395C 53 and 54 can set due to extreme environment temperature conditions and not necessarily due to a camera system defect.

1. Ignition » On / Vehicle » In Service Mode
2. Place vehicle in an area where a ambient temperature is 15–25° C (59–77° F) with engine OFF.
3. Wait at least 30 minutes.
4. Verify DTC B395C is not set
• If DTC B395C is not set

  All OK.

• If DTC B395C is set
5. Replace the component:B225R Sideview Camera - Right
6. Verify DTC B395C is not set
• If DTC B395C is not set

  All OK.

• If DTC B395C is set
7. Replace the component:K157 Video Processing Control Module

Perform the Diagnostic Repair Verification after completing the repair:Diagnostic Repair Verification

• Side View Driver Information Camera Replacement
• For control module replacement, programming, and setup refer to:Control Module References