Control Valve Body Assembly Installation (with ETRS)
Single Use Fasteners and Components
  • Automatic Transmission Fluid Temperature Sensor Seal
  • Clutch Fluid Passage Seal[5x]
  • Fluid Transfer Pipe Seal
Special Tools

DT-36850–A Transjel Lubricant

Equivalent regional tools:Special Tools

Installation Procedure

    Object ID: 5026336
  1. Use DT-36850–A Transjel Lubricant for installing the control valve body ball check valves on-vehicle.
  2. Control Valve Body Ball Check Valve(1)»Install[6x]

    3. Object ID: 5045329
  3. Fluid Transfer Pipe Seal(1)»Install NEW

    4. Caution: Refer to Fastener Caution.

  4. Fluid Transfer Pipe(2)»Install and tighten9 N·m  (80 lb in)

    5. Object ID: 5642872
  5. Clutch Fluid Passage Seal(1)»Install NEW[5x]

    6. Caution: The park release lever must be in the park position to align properly with the piston switch opening prior to installation of the control valve body. Failure to align the components properly may result in damage to the parking servo piston switch.

  6. Place the Park Release Lever in the park position.
  7. The piston switch opening must be positioned correctly. Use appropriate tool to position opening if necessary.
  8. Carefully install the Control Valve Body (2) in the transmission insuring the Park Release Lever aligns inside the Parking Servo Position Switch opening indicated by arrow.
  9. Control Valve Body Bolt(3)»Install and tighten in sequence[5x]8 N·m  (71 lb in)

    10. Object ID: 4572671
  10. Control Valve Solenoid Body(1)»Install
  11. Ensure you connect all the connectors to the control valve solenoid body.
  12. When servicing on-vehicle, the Variable Feed Solenoid Clutch Accumulator Pistons, and Springs may fall out. Control Valve Body Assembly Disassemble
  13. Control Valve Body Bolt(2)»Install and hand tighten[3x]
  14. Control Valve Body Bolt(3)»Install and hand tighten[12x]

    15. Note: Control valve body bolt quantity is wiring harness dependent.

  15. Control Valve Body Bolt(4)»Install and hand tighten[5x]or [6x]

    16. Object ID: 4572673
  16. Automatic Transmission Fluid Temperature Sensor Seal(1)»Install NEW

    17. Note:

    • The bolt retainer area on the wiring harness indicated by arrow may or may not be present. Newer design wiring harness does not have bolt retainer area.
    • The bolts are captured in the wiring harness.
    • Ensure the variable feed solenoid clutch accumulator pistons and springs are installed prior to harness installation.

  17. Automatic Transmission Wiring Harness(2)»Install and tighten8 N·m  (71 lb in)
  18. Ensure you connect all the electrical connectors to the valve body.
  19. Control Valve Solenoid Body Bolt(3)»Install and tighten9 N·m  (80 lb in)

    20. Note: Control valve body bolt quantity is wiring harness dependent.

  20. Control Valve Body Bolt(4)»Install and hand tighten[2x]or [3x]

    21. Object ID: 4806904
  21. Control Valve Body Bolt(1)»Install and tighten in sequence[3x]8 N·m  (71 lb in)
  22. Control Valve Body Bolt(2)»Install and tighten in sequence[12x]8 N·m  (71 lb in)

    Control Valve Body Bolt(3)»Install and tighten in sequence[8x]8 N·m  (71 lb in)


    23. Object ID: 6851755

    Note: The park inhibitor solenoid must be installed after the control valve solenoid body assembly installation to allow for proper alignment.

  23. Park Inhibitor Solenoid(1)»Install
  24. Align the park inhibitor solenoid (1) by pushing and holding it flush against the control valve solenoid body assembly. Continue to hold down the park inhibitor solenoid until the control valve solenoid body bolts (2) are tightened.
  25. Control Valve Solenoid Body Bolt(2)»Install and tighten[2x]8 N·m  (71 lb in)
  26. Connect electrical connector.